SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Screw-Tube Egg Beater: The Tube Spins, the Rod Stands Still
A push-spinning egg beater turns on its point in the bowl: it wanders, and pressing on it slows it.
Walter Hart of Philadelphia received US 31,663, dated 12 March 1861, for an egg beater whose wire beaters are on a tube with a screw thread, spun by a nut slid up and down; inside it a rod fixed to the handle ends in a button that rests on the bottom of the vessel, so "the base ... is stationary and therefore has no tendency to slip" and the pressure is borne by the rod, leaving the tube free to turn.
This rung works out the tube's turns per stroke, then prints the lobed screw tube and nut, fits rod, button and beaters, and times a beating.
Baguhan
About 2 hours, plus printing
Mga Tagubilin
1
1
Turns per stroke
Turns per stroke
Naglo-load ng Jupyter notebook…
2
2
A spiral and slide before it
A spiral and slide before it
The embedded blueprint turns two scrolls with a slide on two spirals. Hart turns one screw tube and stands the whole beater on a still rod.
3
3
Read US 31,663
Read US 31,663
"In my improved egg beater the base, consisting of the button e, which rests on the bottom of the vessel, is stationary and therefore has no tendency to slip and as the pressure imparted to it is sustained by the stationary rod and not by the tube the latter is free to rotate under any pressure to which the instrument may be necessarily subjected."
4
4
Print the tube and nut
Print the tube and nut
Print the three-lobed screw tube (/uploads/blueprints/screw-tube-egg-beater-tube.stl) standing upright, and the nut (/uploads/blueprints/screw-tube-egg-beater-nut.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Mga materyales para sa hakbang na ito:
PETG filament1 pirasoMga kailangang kasangkapan:
Limbagang 3D na FDM5
5
Bend the beaters
Bend the beaters
Bend three loops of stainless wire about 32 mm across and 45 mm high, and epoxy their ends round the tube's lower end.
Mga materyales para sa hakbang na ito:
Kawad na hindi kinakalawang na asero1 piraso
Epoksing dalawang bahagi1 pirasoMga kailangang kasangkapan:
Plais na bilog ang dulo
Plais na Patag ang Nguso6
6
Rod, button and handle
Rod, button and handle
Pass a 5 mm rod through the tube, with the nut on the tube. Epoxy a washer to the rod's foot as the button, leaving the tube 2 mm of play, and a hardwood handle on its top.
Mga materyales para sa hakbang na ito:
Bilog na Bara ng Malambot na Asero1 piraso
Patag na Sinturon1 piraso
Mga tarugong matigas na kahoy1 pirasoEpoksing dalawang bahagi1 pirasoMga kailangang kasangkapan:
Lagaring Pang-metal
Bais sa Mesang Panggawa
Walang-Kableng Barena
Hanay ng Talim ng Barena7
7
The patent drawing
The patent drawing
US 31,663 drawing sheet, public domain (expired patent).
8
8
Beat egg whites
Beat egg whites
Stand the button on the bowl's bottom, hold the handle, and slide the nut up and down; time two whites to stiff peaks. Note whether the button stays put.
Mga materyales para sa hakbang na ito:
Itlog2 pirasoMga kailangang kasangkapan:
Malaking mangkok na panghalo na asero na hindi kinakalawang
Panukat ng Oras9
9
A tube that sticks, a nut that binds
A tube that sticks, a nut that binds
Screw-tube egg beater troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Walter Hart** of Philadelphia received US 31,663, dated 12 March 1861. His thread is three wires coiled on the tube, their lower ends spread into the beaters; the nut is wood with a pin entering between the wires; a strip of metal lapped spirally may replace the wires. He did not claim the screw spindle, beaters and nut as such, which were known, but their combination with the internal rod and button.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. A printed lobed tube stands in for his wire thread. Your times are the result.
Mga Materyales
7- 1 pirasoPlaceholder
- Placeholder
- 2 pirasoPlaceholder
- Placeholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- 2 pirasoPlaceholder
Mga Kinakailangang Kasangkapan
9- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.