Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Siphon Tube: Glass Tube Bent with Drawn-Down Ends (Faraday, 1830)
Charlie

Nilikha ni

Charlie

7. Nobyembre 2026DE
2
0
0
0
0

Siphon Tube: Glass Tube Bent with Drawn-Down Ends (Faraday, 1830)

A glass siphon for drawing clear liquid off a settled deposit, which Michael Faraday (1830) rated far better than pouring. He bends a glass tube about 0.3 inch inside and 22 inches long so that one leg is about 2 inches longer than the other, and draws both ends down to about 0.2 inch. The narrow ends hold the liquid in while one end is closed with a finger; the wide body lets it run fast. Source: M. Faraday, Chemical Manipulation (1830), §550, pp. 241-242. Picture: his text and figure.
Katamtaman
Unknown

Mga Tagubilin

1

Read Faraday

"Let a piece of glass tube, about 0.3 of an inch internal diameter, 22 inches in length, and of sufficient thickness to bear ordinary laboratory work, be bent at the blow-pipe table, so that one limb shall be about two inches longer than the other; the extremities should be contracted at the lamp, until about 0.2 of an inch in diameter."
2

Cut the tube

Take glass tube about 0.3 in. inside diameter, thick enough for ordinary laboratory work, and cut 22 in. off it: make a deep mark round it with the edge of a sharp three-square file, then break it like a stick, pulling the hands slightly apart (§1152). Wall thickness in figures is not given (unknown).

Mga materyales para sa hakbang na ito:

Tubong salaminTubong salamin1 22 in.

Mga kailangang kasangkapan:

Kikil (Kikil na Pangkamay)Kikil (Kikil na Pangkamay)
3

Bend it

Bend the tube in the flame of the blow-pipe table so that one leg is about 2 in. longer than the other. For so sharp a bend, do not bend it all at one spot: heat and bend one part as far as it will go without narrowing the bore, then heat the next part and carry the curve on until the legs are close (§1160).

Mga kailangang kasangkapan:

Pang-ihip ng salamin na pang-mesaPang-ihip ng salamin na pang-mesa
4

Draw down the ends

Heat each end and pull it along its length so that it lengthens and narrows (§1166), until the opening is about 0.2 in. across.

Mga kailangang kasangkapan:

Pang-ihip ng salamin na pang-mesaPang-ihip ng salamin na pang-mesa
5

Use it

Hold the siphon upside down with the short leg higher, fill it with water from Faraday's dropping-bottle (a wash bottle does the same job), holding its beak against the side of the opening so no air bubbles are caught; close the long leg with a finger and fill the short leg too. Turn it over, put the short leg into the liquid and lift the finger: the clear liquid runs out. A finger on the outer end slows or stops it; keep the inner end clear of the deposit (§§550-551).

Mga kailangang kasangkapan:

Bote ng PanlinisBote ng Panlinis

Mga Materyales

1

Mga Kinakailangang Kasangkapan

3

Ang blueprint na ito ay gumagawa ng

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...