Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Youblob · CC0
55-Gallon Open-Head Steel Drum to ICC Specification 17H (1964)
The open-top 55-gallon (208-litre) steel drum, built to the rule US railways and shippers used for single-trip removable-head drums: welded low-carbon steel body, three rolled hoops, a crowned bottom, and a lid clamped by a bolted ring over a gasket.
Source: ICC Specification 17H, 49 CFR 78.118, Federal Register, 29 December 1964. The spec does not say how the bottom is joined. The litre figure, the gasket rubber and the machines are ours. Picture drawn by Youblob.
Abantado
Production line
Mga Tagubilin
1
1
Cut low-carbon steel sheets
Cut low-carbon steel sheets
Use low-carbon steel for body and heads. For a 55-gallon drum: body 18 gauge, bottom head 18 gauge, removable head 14 gauge (16 gauge if the cover has one or more corrugations near its edge). 18 gauge is 0.0478 in nominal and at least 0.0428 in; 14 gauge 0.0747 in and at least 0.0677 in, measured at least 3/8 in from an edge.
Mga materyales para sa hakbang na ito:
Plantsang Malambot na Asero1 body, bottom and lid sheetsMga kailangang kasangkapan:
Malakas na gunting sa metal
Mikrometro2
2
Roll and weld the body
Roll and weld the body
Roll the body sheet into a cylinder and weld the seam. The body seam must be welded.
Mga kailangang kasangkapan:
Pambaluktot ng plantsa
Panghinang ng dugtungan ng tubo3
3
Roll in three hoops
Roll in three hoops
Roll or swage three hoops into the body, one of them near the top curl.
Mga kailangang kasangkapan:
Rodilyong pang-uka4
4
Press crowned heads
Press crowned heads
Press the bottom head crowned (convex) by at least 3/8 in, not standing out beyond the level of the chime, and fit it to the body. The spec does not say how the bottom is joined.
Mga kailangang kasangkapan:
Pisaang pang-stamping5
5
Make the bolted ring and gasket
Make the bolted ring and gasket
Make the closing ring from 12-gauge steel with drop-forged lugs, one of them threaded, and a 5/8 in bolt and nut (for drums over 30 gallons). Fit a gasket under the lid: gaskets are required.
Mga materyales para sa hakbang na ito:
Plantsang Malambot na Asero1 12-gauge strip for the ring
Bilog na barang asero na malambot1 for the lugs
Sari-saring hex bolt1 5/8 in bolt
Tuerkang Heksagonal1 5/8 in
Sapin ng goma1 gasketMga kailangang kasangkapan:
Pambaluktot ng plantsa
Bumabagsak na martilyo na may forging die
Kutsilyong Pang-arte6
6
Check capacity and mark
Check capacity and mark
The drum must hold at least 4 % more than its marked 55 gallons, and no more than 5 % more (or 4 % plus 1 quart, whichever is greater). Emboss the marks: ICC-17H, STC (single-trip container), the maker, and the gauges, capacity and year.
Mga kailangang kasangkapan:
Pisaang pang-stamping7
7
Leak-test every drum
Leak-test every drum
Test each drum by air pressure inside of at least 7 psi with its seams under water or covered with soapsuds or heavy oil. Reject leakers, or repair them the way they were made and test again.
Mga materyales para sa hakbang na ito:
Tubig1 as requiredMga kailangang kasangkapan:
Kompresor ng hangin
Panukat ng Diin8
8
Type tests every four months
Type tests every four months
On drums taken at random and closed as for use: drop one filled with water to 98 % from 4 ft onto concrete so it lands diagonally on the chime, and hold another at 15 psi water pressure for 5 minutes. None may leak.
Mga materyales para sa hakbang na ito:
Tubig1 as requiredMga kailangang kasangkapan:
Panukat ng DiinMga Materyales
6- 1 12-gauge strip for the ringPlaceholder
- 1 for the lugsPlaceholder
- 1 5/8 in boltPlaceholder
- 1 5/8 inPlaceholder
- 1 gasketPlaceholder
- 2 as requiredPlaceholder
Mga Kinakailangang Kasangkapan
10- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.