SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE

Steel Needle: Pointed, Eyed, Hardened in Oil and Tempered
Needles are made from good steel wire: cut, straightened, pointed, flattened and pierced for the eye, hardened by heating and plunging into oil, then tempered back to a springy hardness, scoured and polished (Bucknall Smith, A Treatise upon Wire, 1891). This is the same sequence by hand, one heavy needle at a time from piano wire; the hand methods and sizes are ours.
The picture: steel sewing needles (Wikimedia Commons).
Katamtaman
Half a day
Mga Tagubilin
1
1
Cut, soften and straighten
Cut, soften and straighten
Cut 70 mm of 1.2 mm piano wire. Heat it to red in the forge and let it cool slowly in the ashes so it can be filed and drilled, then roll it straight on the anvil.
Mga materyales para sa hakbang na ito:
Alambre ng piyano70 mmMga kailangang kasangkapan:
Plais na pamutol ng kawad na pahilis
Pandayan ng panday
Plais na matulis ang nguso
Palihan2
2
Point
Point
Clamp it in the vise and file a long, even taper to a sharp point, turning the wire as you go.
Mga kailangang kasangkapan:
Hanay ng Kikil
Bais sa Mesang Panggawa
Salaming pangkaligtasan3
3
Flatten and pierce the eye
Flatten and pierce the eye
Flatten the head end slightly on the anvil, drill the eye through the flat with the finest bit, then file off the burrs and round the head.
Mga kailangang kasangkapan:
Palihan
Martilyong pahalang ang tulis
Barenang de-kamay
Hanay ng Kikil
Bais sa Mesang Panggawa
Salaming pangkaligtasan4
4
Harden in oil
Harden in oil
Heat the needle evenly to red and plunge it into the oil. It is now glass-hard and brittle.
Mga kailangang kasangkapan:
Pandayan ng panday
Plais na matulis ang nguso
Tangke ng pamatid na may langis
Salaming pangkaligtasan5
5
Temper
Temper
Reheat it in the oven to about 600 °F (315 °C) and let it cool slowly to a springy temper. If it came out crooked, straighten it with light blows of a small hammer on the anvil.
Mga kailangang kasangkapan:
Hurno para sa heat treatment
Thermocouple na may basahan
Palihan
Martilyong pahalang ang tulis6
6
Scour and polish
Scour and polish
Scour it bright with emery cloth, a little oil and soap. Wash it in hot water, dry it in sawdust, touch up the point, and polish it on the leather strop.
Mga kailangang kasangkapan:
Telang emeri
Langis ng oliba
Sabon
Kusot
Katad na panghasa
Hanay ng KikilMga Materyales
1- 70 mmPlaceholder
Mga Kinakailangang Kasangkapan
17- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.


