Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Stone Carving Chisels: Mallet-Headed Plain and Tooth Chisels and Points for Soft Stone (Holford, 1907)
H. Holford · Public domain
Forge

Nilikha ni

Forge

4. Nobyembre 2026NO
4
0
0
0
0

Stone Carving Chisels: Mallet-Headed Plain and Tooth Chisels and Points for Soft Stone (Holford, 1907)

Soft stone such as limestone and sandstone is cut with chisels struck by a wooden mallet, so their heads are broad and a little rounded. H. Holford's 20th Century Toolsmith and Steelworker (1907) shows a set: plain chisels, tooth chisels with a row of sharp teeth, and points, forged from 3/4 inch octagon steel of 75 points carbon and tempered a very pale blue. He gives no lengths, widths or tooth spacing; those are unknown here. The brine bath is from his chapter on the hardening bath. Source: H. Holford (1907), pp. 21, 131-133, 140-141. Picture: his Fig. 71.
Katamtaman
A day for a set

Mga Tagubilin

1

Read Holford

"In cutting soft stone of any description wooden mallets are used, consequently the heads of the tools are made broad and a little rounding, so as not to cut or bruise the mallet."
2

Forge the mallet heads

Use 3/4 inch octagon steel of 75 points carbon. For each tool, upset the head end a little, fuller it in, draw it out, then swage it to its broad, slightly rounded shape between top and bottom swages (Fig. 78). For a narrow chisel, forge the head first; for a wide one, forge the cutting end first. Sizes are not given (unknown).

Mga materyales para sa hakbang na ito:

Oktagonal na barang tool steelOktagonal na barang tool steel1 3/4 in octagon

Mga kailangang kasangkapan:

PandayanPandayan
PalihanPalihan
Martilyo ng pandayMartilyo ng panday
ParagosParagos
Fuller (bakal na panguka)Fuller (bakal na panguka)
Itaas at ibabang swageItaas at ibabang swage
Sipit ng pandaySipit ng panday
Hindi alam na sukatHindi alam na sukat
Salaming pangkaligtasanSalaming pangkaligtasan
Guwantes na Matibay sa InitGuwantes na Matibay sa Init
3

Forge the chisels and points

For a wide chisel, upset the end to the width of the chisel before drawing it down to a thin cutting edge. Hammer the flat surfaces. Draw the points down to almost a square point (Fig. 72). For tooth chisels, punch the teeth into the edge in a punch machine after the flat surfaces have been hammered, then file each tooth to an extremely sharp point.

Mga kailangang kasangkapan:

PandayanPandayan
PalihanPalihan
Martilyo ng pandayMartilyo ng panday
Sipit ng pandaySipit ng panday
Pisaang pambutasPisaang pambutas
Pinong kikilPinong kikil
4

Harden the chisels

Heat the cutting edge very evenly along its whole length and dip it at least one inch into the hardening bath (clean water, best as a strong brine, kept large and cold). Polish it bright by rubbing it across a board spread with fine clean sand near the forge, and draw the temper to a very pale blue, the right temper for all limestone tools.

Mga kailangang kasangkapan:

PandayanPandayan
Puspos na solusyon ng asinPuspos na solusyon ng asin
TablaTabla
Pinong BuhanginPinong Buhangin
Sipit ng pandaySipit ng panday
Guwantes na Matibay sa InitGuwantes na Matibay sa Init
5

Harden the points

Dip the points deep into the bath. Draw the temper so it shows at least 5/8 inch back from the point; if it runs so fast that only the very tip is tempered, the point bends and breaks easily.

Mga kailangang kasangkapan:

PandayanPandayan
Puspos na solusyon ng asinPuspos na solusyon ng asin
TablaTabla
Pinong BuhanginPinong Buhangin
Sipit ng pandaySipit ng panday
Guwantes na Matibay sa InitGuwantes na Matibay sa Init
6

History and honest limits

Holford sets the soft-stone tools apart from those for granite and marble: soft stone takes wooden mallets, hence the broad heads, and a very pale blue temper. The finest stone carvers' tools, struck only lightly, he hardens without drawing any temper at all. He gives no lengths, widths or tooth spacing; the tools used to make them are ours.

Mga Materyales

1

Mga Kinakailangang Kasangkapan

15

Ang blueprint na ito ay gumagawa ng

Thumbnail
Placeholder

Mga pait sa paglilok ng bato

Free

35
0
1

Kaugnay na Blueprint

Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo

Stone Carving Hammer: a Granite Cutters' Mash Hammer (Holford, 1907)

Stone Carving Hammer: a Granite Cutters' Mash Hammer (Holford, 1907)

ni ForgeNO

Paggawa ng Metal

5
0
0
0
0
0

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...