SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
The Adjustable Buttonhole Cutter: A Turning Anvil of Many Lengths
Every buttonhole must be the right length for its button: too short and the button will not pass, too long and it slips out. Cutting each one by eye with scissors is slow and uneven.
Peter Bauer of Newark, New Jersey, received US 129,309, dated 16 July 1872, for a cutter with "a hollow anvil or barrel provided with a series of faces of unequal length", turned on the lower jaw so that "button-holes of different lengths, with or without an eye, can be cut with facility".
This rung works out how long a slit a button needs, then cuts test buttonholes on scrap cloth and checks them against the buttons.
Baguhan
About 2 hours
Mga Tagubilin
1
1
Slit length for a button
Slit length for a button
Naglo-load ng Jupyter notebook…
2
2
The other half of the fastening
The other half of the fastening
The embedded blueprint sews a button on. The buttonhole has to be cut to fit it.
3
3
Read US 129,309
Read US 129,309
"The faces of the anvil are of different length, as shown in Fig. 5, and by turning the same round to the position shown in Fig. 2 a long button-hole can be cut with an eye corresponding to the punch c".
"If desired, however, the anvil can be turned to the position shown in Fig. 3, and in this case the punch does not come into action and the button-hole produced is without an eye."
"A gauge, F, is applied on the jaw C to determine the distance of the button-hole from the edge of the material."
4
4
Cut test buttonholes and fit the buttons
Cut test buttonholes and fit the buttons
Measure each button's diameter and thickness with the ruler, and work out its slit length with the notebook.
On a doubled strip of scrap cloth, mark each slit with tailor's chalk, the same distance in from the edge, as Bauer's gauge does. Work a line of small stitches round each mark so the cut edge cannot fray. Lay the cloth on the cutting mat and cut the slit with the craft knife, or with the buttonhole cutter set to that length. For a shank button, punch a small eye at one end.
Push each button through its hole. Note which pass easily, which stick and which slip out.
Mga materyales para sa hakbang na ito:
Telang bulak (magaan)1 piraso
Sinulid na pantahi1 piraso
Set ng butones ng kamiseta1 pirasoMga kailangang kasangkapan:
Pambutas ng ohales
Kutsilyong Pang-arte
Banig na panggupit na kusang naghihilom
Pambutas ng papel
Tisa ng sastre
Karayom sa pananahi
Ruler5
5
A buttonhole that frays, sticks or gapes
A buttonhole that frays, sticks or gapes
Buttonhole troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**Peter Bauer** of Newark, Essex County, New Jersey, received US 129,309, dated 16 July 1872. The patent prints no filing date. He disclaims a solid spiral-grooved cylinder already known for the same purpose.
**Honest limits.** Diameter plus thickness is a rule of thumb, not a standard; stiff or stretchy cloth and the stitching round the hole change the fit. The button sizes and anvil lengths are examples. Your test holes are the measurement.
Mga Materyales
3- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
Mga Kinakailangang Kasangkapan
7- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.