SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
The Bearing-Block Can Opener: Lean on the Wall, Not on the Contents
Pressing on a full can's top to cut it forces the contents up through the cut.
Guy C. Humphries of Washington, D.C., received US 84,122, dated 17 November 1868, for a can and box opener in which a knife-and-handle lever turns on a fulcrum pin through a hinged bearing block whose two faces rest on the can's outside wall; the knife cuts as it rises, and "the pressure at all times being against the outside wall of the can, avoiding the pressing out of the contents."
This rung shows where the cutting force goes, then builds the lever and bearing block and opens a full can.
Katamtaman
About 3 hours
Mga Tagubilin
1
1
Where the force goes
Where the force goes
Naglo-load ng Jupyter notebook…
2
2
A fulcrum on the top before it
A fulcrum on the top before it
The embedded blueprint rests its shoulders on the can's top as the fulcrum. Humphries moves the fulcrum to a block on the outside wall.
3
3
Read US 84,122
Read US 84,122
"When a can or box is to be opened, the point of the knife is driven (vertically) through the top, near to one side, as shown in figs. 1 and 2, until the bearing-block C rests on the outside wall of the vessel. The handle is then depressed, causing the knife to cut as it rises, as shown by dotted and broken lines. The handle is now elevated, and slid along on the top of the vessel, preparatory to a renewal of the cutting-operation, keeping the knife-edge against its kerf."
4
4
Make the knife and handle
Make the knife and handle
Cut 170 mm of 25 × 3 mm flat bar. Shape the last 30 mm into a pointed knife with a cutting edge on its upper side, and twist it to stand on edge. Drill a 5 mm hole 20 mm behind the point.
Mga materyales para sa hakbang na ito:
Patag na Baras na Malambot na Asero1 pirasoMga kailangang kasangkapan:
Lagaring Pang-metal
Bais sa Mesang Panggawa
Kikil (Kikil na Pangkamay)
Hasaan
Walang-Kableng Barena
Hanay ng Talim ng Barena
Malinaw na Salaming Pangkaligtasan5
5
Make the bearing block
Make the bearing block
Cut a hardwood block 18 × 30 × 22 mm. Saw a slot down it for the knife, file a concave face with sharp corners on its underside, and drill it across for the pin.
Mga materyales para sa hakbang na ito:
Tipak ng Matigas na Kahoy1 pirasoMga kailangang kasangkapan:
Lagaring PangkurbaKikil (Kikil na Pangkamay)Walang-Kableng BarenaHanay ng Talim ng BarenaBais sa Mesang Panggawa6
6
Hinge them
Hinge them
Pass an M5 screw through the block and knife with a washer each side and a nut, loose enough for the block to swing.
Mga materyales para sa hakbang na ito:
Mga turnilyo ng makina1 piraso
Patag na Sinturon1 piraso
Tuerkang Heksagonal1 pirasoMga kailangang kasangkapan:
Llaveng ingles7
7
The patent drawing
The patent drawing
US 84,122 drawing sheet, public domain (expired patent).
8
8
Open a full can
Open a full can
Stand a sealed, full can of food on the kitchen scale. Drive the knife in near the edge until the block rests on the wall, cut, slide and cut again round the top; watch for liquid at the cut and read the peak load.
Mga materyales para sa hakbang na ito:
Lata1 pirasoMga kailangang kasangkapan:
Digital na Timbangang Pangkusina
Panukat ng Oras
Guwantes na Katad Pangtrabaho9
9
A block that slips, a knife that sticks
A block that slips, a knife that sticks
Bearing-block can opener troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Guy C. Humphries** of Washington, D.C., received US 84,122, dated 17 November 1868. The fulcrum pin passes loosely through the block and is riveted so the block cannot come off; the fulcrum is midway between the block's two outside edges, preventing slip. The blade may be single or double, edged on one or both sides, for right or left hand. He did not claim a rotary block with a continuous face, nor a stationary block.
**Honest limits.** A hardwood block stands in for his metal one, and a screw for his riveted pin. Your loads are the result.
Mga Materyales
6- Placeholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
- 1 pirasoPlaceholder
Mga Kinakailangang Kasangkapan
12- Placeholder
- Placeholder
- Placeholder
- Placeholder
- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
The Shouldered-Blade Can Opener: The Shoulders Are the Fulcrum
ni Forge
Paggawa ng Metal
30
0
0
0
0
0
The Single-Blow Can Opener: A Ring of Pointed Teeth Punches the Hole
ni Forge
Paggawa ng Metal
26
0
0
0
0
0
The Lid-Lifting Can Opener: One Lip Presses Down While the Other Lifts
ni YourGrandma
PAGKAIN AT INUMIN
38
0
0
0
0
0
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.