SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
The Finger-Valve Fountain Bath Brush: Press to Run, Let Go to Stop
YourGrandma

Nilikha ni

YourGrandma

6. Oktubre 2026IS
29
0
0
0
0

The Finger-Valve Fountain Bath Brush: Press to Run, Let Go to Stop

A bath brush fed from a hose runs all the time, or needs a tap out of reach. Daniel S. Koons and William F. Moughler of Chicago received US 634,527, dated 10 October 1899, for "a fountain bath-brush": a false back with a water passage, joined to the brush by a hollow screw whose perforated head lets the water out among the bristles, with a valve that a spring and the water pressure hold shut until a finger presses its stem, and a strap that holds the hand to the brush. This rung works out the finger force, then builds the false back on a scrub brush with a tyre valve as the finger valve, and measures the force and the flow.
Katamtaman
About 3 hours

Mga Tagubilin

1

Force to open the valve

Naglo-load ng Jupyter notebook…
2

A brush that feeds itself before it

The embedded blueprint feeds soap from inside a shaving brush. Koons and Moughler feed water, and give the finger a valve to start and stop it.
3

Read US 634,527

"Said valve is held normally closed by means of a spring 9 and also by the water-pressure, as will be obvious." "A strap k is secured at the sides of said back B' and passes over the latter, so that by inserting the hand between said back B' and said strap k the brush can be firmly held and the fingers at the same time kept in position to operate the valve."
4

Bore the false back

Cut a hardwood block 120 × 50 × 22 mm. Drill a 6 mm passage 90 mm along its centre from one end, and a 6 mm hole down from the top to meet it 30 mm from the far end.

Mga materyales para sa hakbang na ito:

Tipak ng Matigas na KahoyTipak ng Matigas na Kahoy1 piraso

Mga kailangang kasangkapan:

Bais sa Mesang PanggawaBais sa Mesang Panggawa
Walang-Kableng BarenaWalang-Kableng Barena
Set ng brad point drill bitSet ng brad point drill bit
RulerRuler
Malinaw na Salaming PangkaligtasanMalinaw na Salaming Pangkaligtasan
5

Fit the finger valve

Drill a hole across the passage 20 mm from the inlet to take a tyre valve, pin upward. Epoxy it in so the water must pass through it.

Mga materyales para sa hakbang na ito:

Balbula ng gulongBalbula ng gulong1 piraso
Epoksing dalawang bahagiEpoksing dalawang bahagi1 piraso

Mga kailangang kasangkapan:

Walang-Kableng BarenaWalang-Kableng Barena
Hanay ng Talim ng BarenaHanay ng Talim ng Barena
6

Join it to the brush

Drill a 6 mm hole through the scrub brush's back to line up with the outlet. Cut a rubber gasket, and screw the block on with four wood screws.

Mga materyales para sa hakbang na ito:

Brotsa sa pagkuskosBrotsa sa pagkuskos1 piraso
Plantsa ng gomaPlantsa ng goma1 piraso
Turnilyong pangkahoy #8 x 1"Turnilyong pangkahoy #8 x 1"1 piraso

Mga kailangang kasangkapan:

Walang-Kableng BarenaWalang-Kableng Barena
Hanay ng Talim ng BarenaHanay ng Talim ng Barena
Kutsilyong Pang-arteKutsilyong Pang-arte
Set ng mga distornilyadorSet ng mga distornilyador
7

Strap and hose

Screw a strip of rubber sheet across the block as a hand strap, over the valve's side. Fit a hose connector to the inlet with brass fittings and PTFE tape.

Mga materyales para sa hakbang na ito:

Plantsa ng gomaPlantsa ng goma1 piraso
Turnilyong pangkahoy #8 x 1"Turnilyong pangkahoy #8 x 1"1 piraso
Kabit na tansoKabit na tanso1 piraso
Teyp na PTFE na pantakip ng sinulidTeyp na PTFE na pantakip ng sinulid1 piraso

Mga kailangang kasangkapan:

Set ng mga distornilyadorSet ng mga distornilyador
Llaveng inglesLlaveng ingles
8

The patent drawing

US 634,527 drawing sheet, public domain (expired patent).
Hakbang 8 - Image 1
9

Measure force and flow

Connect the garden hose and turn on the tap. Press the valve pin with the force meter's hook until water runs; note the force. Hold it open over the jug for 30 s and read the flow.
Hakbang 9 - Image 1

Mga materyales para sa hakbang na ito:

Hose sa hardinHose sa hardin1 piraso
TubigTubig1 piraso

Mga kailangang kasangkapan:

Panukat ng Puwersa (Timbangang Spring)Panukat ng Puwersa (Timbangang Spring)
Pitsel na panukatPitsel na panukat
Panukat ng OrasPanukat ng Oras
10

A valve that drips, sticks or barely flows

Finger-valve bath brush troubleshooting.

Flow

Loading...
11

History and honest limits

**Daniel S. Koons** and **William F. Moughler** of Chicago filed US 634,527 on 21 September 1898; it is dated 10 October 1899. They called it a self-cleansing brush. Its handle is telescopic, with a stuffing-box between the two members, and the hose can be led through it to the brush; a second form uses a nozzle as the screw joining the backs. They did not limit it to the bath. **Honest limits.** A tyre valve stands in for their seated valve and stem, and wood screws for their hollow screw. Your forces and flows are the result.

Mga Materyales

10

Mga Kinakailangang Kasangkapan

12

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...