Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
The States of Clay: Five Conditions, and What Each One Will Let You Do
Clay

Nilikha ni

Clay

24. Setyembre 2026DK
43
0
0
0
0

The States of Clay: Five Conditions, and What Each One Will Let You Do

Clay is not one material. It passes through five distinct conditions on its way to being a pot, and each one allows some operations and forbids others — so almost every question in pottery begins with "what state is it in?" SLIP is liquid, for joining and decorating. PLASTIC is workable, for forming. LEATHER-HARD holds its shape but can still be cut, for trimming and handles. BONE DRY is brittle and can only be fired. FIRED is permanent and nothing can be undone. The transitions are one-way in the sense that matters: the first four can be reversed with water, and the fifth cannot be reversed at all. Everything before the kiln is recoverable, and that is worth knowing while learning.
Baguhan
3 hours

Mga Tagubilin

1

What each state is for

PLASTIC clay takes a shape and holds it. Throwing, pinching, coiling and slab building all happen here, and so does joining — the clay is wet enough that two pieces scored and slipped together actually knit. LEATHER-HARD is the state people underuse. It is firm enough to pick up and turn over, soft enough to carve, trim and cut cleanly. Handles are attached here, feet are trimmed here, and carved decoration is done here because it does not smear. BONE DRY is pale, cool to the touch, and extremely fragile. Nothing can be done except sponging the sharpest edges and loading the kiln. Clay that still feels COLD against your cheek is not bone dry, however dry it looks — and firing it wet is the other way pots explode.

Mga materyales para sa hakbang na ito:

LuwadLuwad2 kg
TubigTubig1 litro

Mga kailangang kasangkapan:

Set ng kasangkapan sa luwadSet ng kasangkapan sa luwad
Kasangkapang tadyang na kahoy ng magpapalayokKasangkapang tadyang na kahoy ng magpapalayok
EsponghaEspongha
2

Shrinkage: how much smaller it gets, and when

Naglo-load ng Jupyter notebook…

Mga materyales para sa hakbang na ito:

LuwadLuwad1 kg
Luwad na palayokLuwad na palayok1 kg

Mga kailangang kasangkapan:

RulerRuler
Digital na Kalibrador 6 PulgadaDigital na Kalibrador 6 Pulgada
Desktop na KompyuterDesktop na Kompyuter
Set ng kasangkapan sa luwadSet ng kasangkapan sa luwad
3

Slow the drying down, and slow the edges down most

A pot dries from the outside in and from the rim down, because those parts are most exposed. Thin rims, handles and feet dry first, shrink first, and are held back by the wetter body they are attached to — which is exactly how cracks start. So cover the work loosely with plastic and let it dry SLOWLY and evenly. A day or two under plastic, then a day in the open, beats a morning in a draught every time. Cover the parts that would otherwise race ahead. A strip of plastic over just the rim, or over the handles, lets the thick body catch up — which is the same principle as the thin-bits-burn-first problem in the forge.

Mga materyales para sa hakbang na ito:

LuwadLuwad1 kg

Mga kailangang kasangkapan:

Canvas na pagawaan ng palayokCanvas na pagawaan ng palayok
EsponghaEspongha
4

Joining: score, slip, and only while plastic

Two pieces of clay join properly only when both are the same state and wet enough for their particles to interlock. Score both faces with cross-hatching, wet them with slip made from the SAME clay body, press together and work the seam. Slip from a different body is a common and avoidable mistake: two bodies shrink by different amounts, so the joint is pulling itself apart from the moment it dries. A handle attached to a leather-hard pot is the classic failure. The pot has done most of its drying shrinkage and the handle has not, so the handle shrinks onto a body that cannot move and cracks at the join. Attach at the same state, or bring the handle back to match.

Mga materyales para sa hakbang na ito:

LuwadLuwad1 kg
TubigTubig1 litro

Mga kailangang kasangkapan:

Kasangkapang panggasgas ng luwadKasangkapang panggasgas ng luwad
Set ng kasangkapan sa luwadSet ng kasangkapan sa luwad
EsponghaEspongha

Mga Materyales

3
  • 5 kg
    Placeholder
  • 2 litro
    Placeholder
  • Placeholder

Mga Kinakailangang Kasangkapan

8

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...