Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle.
Painted red inside and light green outside, lined in a lighter colour and black.
Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
Katamtaman
Unknown
Mga Tagubilin
1
1
Make the hales
Make the hales
Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.
Mga materyales para sa hakbang na ito:
Tabla ng kahoy na ash1 hales 3 ft 1 in x 1 5/8 x 1 1/2 inMga kailangang kasangkapan:
Lagaring Pangkamay
Katam
Katam na dalawa ang hawakan2
2
Frame with oak cross-pieces
Frame with oak cross-pieces
Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.
Mga materyales para sa hakbang na ito:
Tablang puting roble1 piraso
Pasak na kahoy1 3/16 in pinsMga kailangang kasangkapan:
Lagaring may gulugod
Pait sa pag-uka ng mortise
Panandang gauge
Barena at talim
Panukat ng anggulong naiaayos3
3
Fit the legs and stays
Fit the legs and stays
Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.
Mga materyales para sa hakbang na ito:
Tablang puting roble1 legs 1 1/2 in square, stays
Bolt na bilog ang ulo at parisukat ang leeg4 3 inMga kailangang kasangkapan:
Lagaring PangkamayBarena at talim
Set ng mga distornilyador4
4
Bottom and sides
Bottom and sides
Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.
Mga materyales para sa hakbang na ito:
Tablang pino1 1/2 in bottom, 5/8 in sides
Pinturang langis1 pirasoMga kailangang kasangkapan:
Lagaring PangkamayKatam
Set ng brotsa5
5
Front board and ironwork
Front board and ironwork
Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.
Mga materyales para sa hakbang na ito:
Tablang pino1 3/4 in front board
Pakong Bakal1 1 1/2 in cut nails
Patag na Baras na Malambot na Asero1 7/8 in hoop iron
Mga turnilyong pangkahoy1 3/4 in round-headedPinturang langis1 pirasoMga kailangang kasangkapan:
Lagaring Pangkamay
MartilyoSet ng mga distornilyadorSet ng brotsa6
6
Make the wheel
Make the wheel
Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.
Mga materyales para sa hakbang na ito:
Tabla ng kahoy na ash1 axle and felloesTablang puting roble1 spokes
Bilog na baras na bakal1 3/8 in pinsPasak na kahoy4 1/4 inPatag na Baras na Malambot na Asero1 3/4 x 1/8 in tyreMga kailangang kasangkapan:
Torno sa kahoyKatam na dalawa ang hawakanBarena at talimMartilyo7
7
Hang the wheel and paint
Hang the wheel and paint
Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.
Mga materyales para sa hakbang na ito:
Patag na Baras na Malambot na Asero2 3/4 x 1/8 in ironsMga turnilyong pangkahoy1 pirasoPinturang langis1 pirasoMga kailangang kasangkapan:
Set ng mga distornilyadorSet ng brotsaMga Materyales
10- 1 axle and felloesPlaceholder
- 1 spokesPlaceholder
- 4 1/4 inPlaceholder
- Placeholder
- 1 3/4 in front boardPlaceholder
- 3 pirasoPlaceholder
- 1 1 1/2 in cut nailsPlaceholder
- 2 3/4 x 1/8 in ironsPlaceholder
- 1 pirasoPlaceholder
- 1 3/8 in pinsPlaceholder
Mga Kinakailangang Kasangkapan
12- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.