Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Workbench: a Pine Bench with a Laminated Maple Top and Vise (Boy Mechanic, 1913)
The same pine bench with a harder top: 14 maple strips set on edge, glued and screwed together, with a back board, a tool rack and a wooden vise on an iron bench screw.
Source: C. E. McKinney, Jr., 'Homemade Workbench', The Boy Mechanic, Book 1 (1913), pp. 442-443. Picture: Figs. 1-3 of the book.
Katamtaman
Unknown
Mga Tagubilin
1
1
Make the two leg frames
Make the two leg frames
Cut four 2 x 4 in pine legs 23 in long with a tenon on each end 1/2 in thick, 3 1/2 in wide and 1 1/2 in long (Fig. 1, A and B). Cut four crosspieces of the same stock 20 in long, mortised in the narrow edge 1 1/4 in from each end, and slope their corners from the leg out to the middle. Fit each pair of legs to a pair of crosspieces to make the two supports.
Mga materyales para sa hakbang na ito:
Kahoy na pino1 2 x 4 in: legs, crosspiecesMga kailangang kasangkapan:
Lagaring Pangkamay
Pait sa pag-uka ng mortise
Martilyo2
2
Brace them together
Brace them together
Join the supports with two 2 x 4 in braces 24 in long, ends sawn square. Bore through each leg and 4 in into the centre of each brace end, bore an intersecting hole on the back of each brace for the nut, and draw each joint tight with a 3/8 x 6 in bolt (Fig. 2, J). A cross brace on the back stops rocking when planing.
Mga materyales para sa hakbang na ito:
Kahoy na pino1 2 x 4 in: braces
Bolt na bilog ang ulo at parisukat ang leeg4 3/8 x 6 inMga kailangang kasangkapan:
Lagaring Pangkamay
Barena at talim
Llaveng ingles3
3
Build up the maple top
Build up the maple top
Make the main top M of 14 maple strips 7/8 in thick, 2 in wide and 3 1/2 ft long, set on edge, each glued and screwed to the next, all with the grain one way so it planes smooth. Rabbet its back edge 1/2 in to take a back board N of the same length, 8 1/2 in wide and 7/8 in thick. Screw the top to the top crosspieces with long screws.
Mga materyales para sa hakbang na ito:
Hindi kilalang materyal14 maple strips 7/8 x 2 in x 3 1/2 ft
Pandikit sa Kahoy1 piraso
Tablang pino1 back board
Mga turnilyong pangkahoy1 pirasoMga kailangang kasangkapan:
Lagaring Pangkamay
Block plane
Distornilyador na patag4
4
Add the tool rack
Add the tool rack
Nail a board E 10 in wide to the back of the bench and fasten a 2 1/2 in board F on top of it at right angles; both 7/8 in thick and 3 1/2 ft long. Bore holes or cut notches in F to hold tools.
Mga materyales para sa hakbang na ito:
Tablang pino2 7/8 in, 3 1/2 ft
Mga pako1 pirasoMga kailangang kasangkapan:
Barena at talimLagaring PangkamayMartilyo5
5
Fit the vise
Fit the vise
Fasten an iron bench screw in a 2 x 6 in block 12 in long. Mortise two guide rails 7/8 x 1 1/2 in and 20 in long into the block; they slide in mortises in a 2 x 4 piece L bolted under the top, which holds the bench-screw nut between the two mortises. Nail L to a top crosspiece and to a 2 x 4 piece P bolted under the top at the end (Fig. 3).
Mga materyales para sa hakbang na ito:
Kahoy na pino1 2 x 6 block, 2 x 4 pieces, guide rails
Tornilyo ng bangko para sa paglililok1 pirasoBolt na bilog ang ulo at parisukat ang leeg1 for L and PMga pako1 pirasoMga kailangang kasangkapan:
Lagaring PangkamayPait sa pag-uka ng mortiseBarena at talimLlaveng inglesMartilyoMga Materyales
8- 1 2 x 6 block, 2 x 4 pieces, guide railsPlaceholder
- 1 for L and PPlaceholder
- 14 maple strips 7/8 x 2 in x 3 1/2 ftPlaceholder
- 1 pirasoPlaceholder
- 2 7/8 in, 3 1/2 ftPlaceholder
- 1 pirasoPlaceholder
- 2 pirasoPlaceholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.