تعاون
فن
خوبصورتی اور تندرستی
دستکاری
ثقافت اور تاریخ
تفریح
ماحول
خوراک اور مشروبات
ریورس انجینئرنگ
سائنسز
کھیل
ٹیکنالوجی
پہننے والے آلات
Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)
Forge

تخلیق کار

Forge

13. نومبر 2026NO
0
0
0
0
0

Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)

Ferdinand H. Dalrymple of Bedford, Ohio, received US 2,163,315, dated 20 June 1939, for a shaft collar "comprised of few parts which are readily obtainable as standard market articles". Two washers are held apart by nuts welded between them. The nuts' inner faces rest on the shaft, and a set screw in one nut's thread holds it. It needs no machining. He says it is stronger, lighter and cheaper than a cast collar, and breaks less readily under a hammer. It also touches the shaft only along lines, so it rusts to it less, and oil can be put in between the nuts. The patent gives no sizes for this form; every size here is ours.
نیا سیکھنے والا
About 1 hour

ہدایات

1

Will it fit together?

Jupyter نوٹ بک لوڈ ہو رہی ہے…
2

Read US 2,163,315

"Preferably, I use as plates standard washers of suitable dimension, and I use as blocks standard nuts." "Inasmuch as the space between the plates is not sufficient for the convenient manipulation of an ordinary wrench, I use socketed set screws for securing the collar to the shaft."
3

Set the parts up on a bar

Use plain steel washers and nuts, not zinc-plated ones. Wire-brush them clean. Grip a 16 mm round bar upright in the vice. Slide one washer onto it, stand four M8 nuts on the washer round the bar at quarter turns, each with a flat down and its hole pointing at the bar's centre and its inner face against the bar. Put the second washer on top and squeeze the stack with the C-clamp; check with the square that the washers are parallel.

اس مرحلے کے لیے مواد:

چپٹا چھلاچپٹا چھلا2 ٹکڑے
چھ گوشہ ڈھبریچھ گوشہ ڈھبری4 ٹکڑے

درکار اوزار:

نرم فولاد کی گول سلاخنرم فولاد کی گول سلاخ
میز کا شکنجہمیز کا شکنجہ
سی شکل کا کلیمپسی شکل کا کلیمپ
تار برش کا سیٹتار برش کا سیٹ
مرکب گنیامرکب گنیا
ڈیجیٹل ورنیئر کیلیپر ۶ انچڈیجیٹل ورنیئر کیلیپر ۶ انچ
4

Weld the nuts to the washers

Wearing the helmet and gloves, tack each nut to both washers with a short fillet weld at its outer corner, keeping the arc away from the bar. Let it cool, lift the collar off the bar, and run a fillet along both ends of every nut on both washers. Chip and wire-brush the slag. Run the set screw in and out of one nut to clear any spatter from its thread, and file the bore ends smooth.

اس مرحلے کے لیے مواد:

ویلڈنگ الیکٹروڈویلڈنگ الیکٹروڈ4 ٹکڑے

درکار اوزار:

آرک ویلڈنگ مشینآرک ویلڈنگ مشین
خود بخود سیاہ ہونے والا ویلڈنگ ہیلمٹخود بخود سیاہ ہونے والا ویلڈنگ ہیلمٹ
ویلڈنگ کے دستانےویلڈنگ کے دستانے
تار برش کا سیٹتار برش کا سیٹ
اینگل گرائنڈراینگل گرائنڈر
ریتیوں کا سیٹریتیوں کا سیٹ
حفاظتی عینکحفاظتی عینک
5

The collar in 3D

FreeCAD model, our sizes: the two 50 mm washers, the four M8 nuts between them at quarter turns, their inner faces on a 16 mm shaft, and the socket set screw in one nut. The welds are not modelled.
ڈیزائن فائلSTLCC0 - Free
6

Fit it on the shaft

Run an M8 x 8 cup point socket set screw into one nut from outside. Slide the collar onto the shaft to its place and tighten the screw with the hex key between the washers. Try to slide and turn it; it must not move.

اس مرحلے کے لیے مواد:

پیالہ نما سرے والا سیٹ اسکروپیالہ نما سرے والا سیٹ اسکرو1 ٹکڑا

درکار اوزار:

ایلن کنجی سیٹایلن کنجی سیٹ
7

Troubleshooting

Built-up collar troubleshooting.

Flow

Loading...
8

History and honest limits

**Ferdinand H. Dalrymple** of Bedford, Ohio, US 2,163,315, dated 20 June 1939, filed 2 November 1937. He claimed "opposed spaced plane plates formed with coaxial bores for the reception of a shaft, transverse spaced internally-threaded blocks welded to the opposed faces of the plates and serving as the sole means for holding the plates in relatively fixed positions, and set screws engaging the blocks". His Figs. 8 and 9 use standard square nuts and socketed set screws; we use hex nuts, as his Figs. 1-5 allow "standard nuts". His patent also shows special blocks, flanged plates, three-plate and split forms; we build the simplest. He gives no sizes for this form; every size here is ours.

مواد

4

درکار اوزار

13

ڈیزائن فائلیں

1

یہ بلوپرنٹ بناتا ہے

CC0 پبلک ڈومین

یہ بلیو پرنٹ CC0 کے تحت جاری کیا گیا ہے۔ آپ اجازت لیے بغیر اس کام کو نقل، ترمیم، تقسیم اور کسی بھی مقصد کے لیے استعمال کرنے کے لیے آزاد ہیں۔

میکر کی حمایت کریں ان کے بلیو پرنٹ کے ذریعے پروڈکٹس خرید کر جہاں وہ میکر کمیشن وینڈرز کی طرف سے مقرر، کماتے ہیں، یا اس بلیو پرنٹ کی نئی تکرار بنائیں اور آمدنی شیئر کرنے کے لیے اسے اپنے بلیو پرنٹ میں کنکشن کے طور پر شامل کریں۔

بحث

(0)

لاگ ان بحث میں شامل ہونے کے لیے

تبصرے لوڈ ہو رہے ہیں...