فن
خوبصورتی اور تندرستی
دستکاری
ثقافت اور تاریخ
تفریح
ماحول
خوراک اور مشروبات
ریورس انجینئرنگ
سائنسز
کھیل
ٹیکنالوجی
پہننے والے آلات
Extruded Polystyrene Foam
Emma

تخلیق کار

Emma

22. ستمبر 2026SE
1
0
0
0
0

Extruded Polystyrene Foam

Carl Munters had shown that polystyrene heated with methyl chloride under pressure puffs into a closed-cell foam when let out of the vessel (US 2,023,204) - but only in small pieces; with larger outlets the mass collapsed into brittle, irregular lumps. Otis Ray McIntire at Dow found the fix: keep the mass BELOW the critical temperature of methyl chloride, about 143 °C, so the gas stays dissolved, and let its own evaporation cool the foam fast enough to freeze the cells. **US 2,450,436**, "Manufacture of cellular thermoplastic products", McIntire, assigned to Dow Chemical, filed 26. July 1947, granted 5. October 1948. Its drawing is the pressure vessel with the bottom valve the foam flows out of. Dow sold the result as blue insulation board; the white bead foam of packaging is a later process. **Methyl chloride is toxic; you start from foam board.** You build a hot-wire cutter, cut an insulated box, and measure how long it keeps ice.
نیا سیکھنے والا
3 hours plus an ice test

ہدایات

1

The cutter

Base on two feet, a post and an arm; the wire runs from the arm tip down through the base to a spring underneath.
ڈیزائن فائلBLENDCC0 - Free
2

Build the frame

From 18 mm plywood cut a 300 x 300 mm base, two 300 x 40 mm feet, a 280 x 50 mm post and a 200 x 50 mm arm. Glue and screw the post to the back edge and the arm square on top.

اس مرحلے کے لیے مواد:

پلائی ووڈ کی چادرپلائی ووڈ کی چادر1 ٹکڑا
لکڑی کے پیچلکڑی کے پیچ10 ٹکڑے
لکڑی کا گوندلکڑی کا گوند20 ملی لیٹر

درکار اوزار:

ہاتھ کی آریہاتھ کی آری
بے تار مشقبے تار مشق
پیچ کس سیٹپیچ کس سیٹ
فولادی پیمانہفولادی پیمانہ
3

String the wire

Drill 2 mm through the arm tip and the base directly below. Fix the wire to an eye bolt on top of the arm, run it down through the base, and tie it to a spring under the base so it stays taut when it expands hot. Check it is square to the table.

اس مرحلے کے لیے مواد:

نائکروم ۸۰/۲۰ تار، ۰٫۶۴ ملی میٹرنائکروم ۸۰/۲۰ تار، ۰٫۶۴ ملی میٹر1 میٹر
آنکھ والا بولٹآنکھ والا بولٹ1 ٹکڑا
دباؤ کے کمانی سیٹدباؤ کے کمانی سیٹ1 سیٹ

درکار اوزار:

بے تار مشقبے تار مشق
ڈبے میں مشقوں کا سیٹڈبے میں مشقوں کا سیٹ
4

Power it

Clip leads to the wire at the arm and below the base. Set the bench supply to 1.5 V with a 4 A limit and raise it slowly (notebook) until the wire slides through a scrap cleanly. Ventilate.

درکار اوزار:

قابلِ ترتیب میز کی بجلی سپلائیقابلِ ترتیب میز کی بجلی سپلائی
Alligator to Alligator CablesAlligator to Alligator Cables
N95 تنفسی ماسکN95 تنفسی ماسک
شفاف حفاظتی عینکشفاف حفاظتی عینک
5

Cut the box

From 25 mm foam board cut a base and lid 200 x 200 mm, two sides 200 x 150 mm and two 150 x 150 mm. Feed slowly - let the wire do the work. Tape the box together.

اس مرحلے کے لیے مواد:

اخراج شدہ پولی سٹائرین فوم بورڈاخراج شدہ پولی سٹائرین فوم بورڈ1 شیٹ
ماسکنگ ٹیپماسکنگ ٹیپ1 رول

درکار اوزار:

فولادی پیمانہفولادی پیمانہ
6

Weigh a cube

Cut a 50 mm cube from an offcut and weigh it for the notebook.

درکار اوزار:

ڈیجیٹل باورچی خانہ ترازوڈیجیٹل باورچی خانہ ترازو
7

The ice test

Put 500 g of ice in a bag in the foam box and another 500 g in a cardboard box of the same size, side by side in the same room. Note the room temperature and check both every hour until the ice is gone.

اس مرحلے کے لیے مواد:

برف کے ٹکڑےبرف کے ٹکڑے1000 گرام
لہریا گتّے کا ڈبہلہریا گتّے کا ڈبہ1 ٹکڑا

درکار اوزار:

ڈیجیٹل باورچی خانہ ترازوڈیجیٹل باورچی خانہ ترازو
کمرے کا تھرمامیٹرکمرے کا تھرمامیٹر
8

Wire, density, heat leak

Jupyter نوٹ بک لوڈ ہو رہی ہے…
9

History & Context

**What the patent specifies:** polystyrene with methyl chloride dissolved under pressure below the gas's critical temperature, released through an outlet so evaporation expands and cools it into uniform closed cells, in blocks 2 inches thick or more. **Modern build (derived):** commercial extruded foam board, today made with other blowing agents. The patent names its target plainly: blocks big enough to cut into insulating panels for refrigerators. Its limits: it melts at low heat, burns unless treated, dissolves in many solvents (and in some glues and paints), and breaks down in sunlight.
قدم 9 - Image 1

مواد

10

درکار اوزار

11

ڈیزائن فائلیں

1

متعلقہ بلیو پرنٹ

یہ بلیو پرنٹ علم بانٹتے ہیں — تکنیک، مواد یا اصول

CC0 پبلک ڈومین

یہ بلیو پرنٹ CC0 کے تحت جاری کیا گیا ہے۔ آپ اجازت لیے بغیر اس کام کو نقل، ترمیم، تقسیم اور کسی بھی مقصد کے لیے استعمال کرنے کے لیے آزاد ہیں۔

میکر کی حمایت کریں ان کے بلیو پرنٹ کے ذریعے پروڈکٹس خرید کر جہاں وہ میکر کمیشن وینڈرز کی طرف سے مقرر، کماتے ہیں، یا اس بلیو پرنٹ کی نئی تکرار بنائیں اور آمدنی شیئر کرنے کے لیے اسے اپنے بلیو پرنٹ میں کنکشن کے طور پر شامل کریں۔

بحث

(0)

لاگ ان بحث میں شامل ہونے کے لیے

تبصرے لوڈ ہو رہے ہیں...