تعاون
فن
خوبصورتی اور تندرستی
دستکاری
ثقافت اور تاریخ
تفریح
ماحول
خوراک اور مشروبات
ریورس انجینئرنگ
سائنسز
کھیل
ٹیکنالوجی
پہننے والے آلات
Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)
Forge

تخلیق کار

Forge

13. نومبر 2026NO
9
0
0
0
0

Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)

Henry Gibbs of Chicago received US 683,645, dated 1 October 1901, for a lawn sprinkler "operating on the familiar Barker's mill principle": water leaving its arms sideways pushes the head round. His head turns on a ring of steel balls held in matching grooves in the head and in the end of the supply pipe, so it spins freely with little friction and stays on. We turn the head from brass and the groove in a steel pipe on the lathe. All sizes are ours.
درمیانہ
About 5 hours

ہدایات

1

How many balls

Jupyter نوٹ بک لوڈ ہو رہی ہے…
2

Read US 683,645

"It being only necessary that certain of the orifices shall discharge the water tangentially to revolve the head 14 and spray-pipes 15 in the well-known manner."
3

Groove the supply pipe

Chuck a length of steel pipe (his pipe 13) and finish its top end smooth and round. Cut a half-round groove (his 17) round it a little below the end, to the depth the notebook gives, with a round-nosed tool. Use thick-walled pipe, so at least 1.5 mm of wall is left under the groove (ours).

اس مرحلے کے لیے مواد:

فولادی پائپ (موٹی دیوار، چُوڑی دار سرے)فولادی پائپ (موٹی دیوار، چُوڑی دار سرے)1 ٹکڑا

درکار اوزار:

دھات کی خراددھات کی خراد
تین جبڑوں والا خراد چکتین جبڑوں والا خراد چک
خراد کا کاٹنے کا اوزارخراد کا کاٹنے کا اوزار
ڈیجیٹل ورنیئر کیلیپر ۶ انچڈیجیٹل ورنیئر کیلیپر ۶ انچ
4

Turn the head

Turn a brass bar to a short round head (his 14). Bore it from below to loosely fit the pipe end, his bore 16, but stop short of the top so a lip (his flange 22) overhangs the pipe end. Cut a matching groove 18 inside the bore at the same height as the pipe's groove.

اس مرحلے کے لیے مواد:

پیتل کی گول سلاخپیتل کی گول سلاخ1 ٹکڑا

درکار اوزار:

دھات کی خراددھات کی خراد
تین جبڑوں والا خراد چکتین جبڑوں والا خراد چک
خراد کا کاٹنے کا اوزارخراد کا کاٹنے کا اوزار
سینٹر ڈرل سیٹسینٹر ڈرل سیٹ
مشقوں کا سیٹمشقوں کا سیٹ
ڈیجیٹل ورنیئر کیلیپر ۶ انچڈیجیٹل ورنیئر کیلیپر ۶ انچ
5

Drill the ball hole and the arms

Drill a hole (his opening 20) through the head's side into the groove, just bigger than a ball, and tap it for a screw plug (21). Drill three holes round the head into the bore for the spray pipes.

درکار اوزار:

ستون والی مشق مشینستون والی مشق مشین
مشقوں کا سیٹمشقوں کا سیٹ
چُوڑی کاٹنے کا سیٹچُوڑی کاٹنے کا سیٹ
میز کا شکنجہمیز کا شکنجہ
6

Make the spray pipes

Cut three lengths of copper tube, close their outer ends, and bend the last bit of each upward as his Fig. 1. Drill small holes near the ends, some pointing sideways (tangentially), all the same way round, so the jets turn the head. Solder the pipes into the head's holes (ours; he threads them in).

اس مرحلے کے لیے مواد:

تانبے کی نلکیتانبے کی نلکی1 ٹکڑا
ٹن-سیسے کا ٹانکہٹن-سیسے کا ٹانکہ1 ٹکڑا
فلکسفلکس1 ٹکڑا

درکار اوزار:

لوہا کاٹنے کی آریلوہا کاٹنے کی آری
مشقوں کا سیٹمشقوں کا سیٹ
ستون والی مشق مشینستون والی مشق مشین
برقی سولڈرنگ آئرنبرقی سولڈرنگ آئرن
میز کا شکنجہمیز کا شکنجہ
7

Assemble with the balls

Slide the head onto the pipe end with the grooves level. Feed balls in through the side hole, turning the head, until the race is full; then screw in the plug. The head should spin freely and not lift off.

اس مرحلے کے لیے مواد:

فولادی بال بیئرنگ (سیٹ)فولادی بال بیئرنگ (سیٹ)1 ٹکڑا
مشینی پیچمشینی پیچ1 ٹکڑا

درکار اوزار:

انگریزی پاناانگریزی پانا
8

Make the stand

Bore a hardwood block to hold the pipe upright and glue in three splayed dowel legs (ours; his base 10 and supports 11). Screw the hose coupling onto the pipe's lower end below the block (his coupling 12).

اس مرحلے کے لیے مواد:

سخت لکڑی کا ٹکڑاسخت لکڑی کا ٹکڑا1 ٹکڑا
سخت لکڑی کی کھونٹیاںسخت لکڑی کی کھونٹیاں1 ٹکڑا
لکڑی کا گوندلکڑی کا گوند1 ٹکڑا
ہوز کپلنگہوز کپلنگ1 ٹکڑا

درکار اوزار:

ہاتھ کی آریہاتھ کی آری
ستون والی مشق مشینستون والی مشق مشین
مشقوں کا سیٹمشقوں کا سیٹ
9

Run it

Connect a garden hose and turn on the water slowly: the jets push the head round and throw the water in a circle. More pressure turns it faster.
10

Troubleshooting

Lawn sprinkler troubleshooting.

Flow

Loading...
11

History and honest limits

**Henry Gibbs** of Chicago, assignor to W. D. Allen Manufacturing Company, US 683,645, dated 1 October 1901, filed 20 May 1901. He claimed a single-piece hollow coupling with radial spray pipes having tangential orifices, a bore loosely fitting the supply pipe, "annular grooves in the opposed cylindrical faces of said bore and said pipe" and "bearing balls interposed in said grooves". He gives no sizes or metals; the brass, steel pipe, ball size, soldered copper arms and the wooden stand are ours.

مواد

11

درکار اوزار

13

یہ بلوپرنٹ بناتا ہے

CC0 پبلک ڈومین

یہ بلیو پرنٹ CC0 کے تحت جاری کیا گیا ہے۔ آپ اجازت لیے بغیر اس کام کو نقل، ترمیم، تقسیم اور کسی بھی مقصد کے لیے استعمال کرنے کے لیے آزاد ہیں۔

میکر کی حمایت کریں ان کے بلیو پرنٹ کے ذریعے پروڈکٹس خرید کر جہاں وہ میکر کمیشن وینڈرز کی طرف سے مقرر، کماتے ہیں، یا اس بلیو پرنٹ کی نئی تکرار بنائیں اور آمدنی شیئر کرنے کے لیے اسے اپنے بلیو پرنٹ میں کنکشن کے طور پر شامل کریں۔

بحث

(0)

لاگ ان بحث میں شامل ہونے کے لیے

تبصرے لوڈ ہو رہے ہیں...