فن
خوبصورتی اور تندرستی
دستکاری
ثقافت اور تاریخ
تفریح
ماحول
خوراک اور مشروبات
ریورس انجینئرنگ
سائنسز
کھیل
ٹیکنالوجی
پہننے والے آلات
Pneumatic Tube Post
Ed

تخلیق کار

Ed

20. اگست 2026FI
1
0
0
0
0

Pneumatic Tube Post

Before the telephone, the fastest way to move a message across a city was to put it in a cylinder and blow it through a pipe. A carrier sealed by felt or leather rings fits the bore closely; make a pressure difference across it — pump air in behind or suck it out ahead — and the carrier is driven along at twenty or thirty miles an hour, around corners, under streets, from one building to another. London's first line opened in 1853 between the Stock Exchange and a telegraph office; Paris built a network of hundreds of kilometres that carried the petit bleu until 1984. It is an unglamorous piece of engineering that solved a real problem: a telegram still had to be physically carried from the telegraph office to the recipient, and the tube did that leg faster than any messenger could.
نیا سیکھنے والا
45 minutes

ہدایات

1

Build the tube and a carrier

The fit between carrier and bore is the whole engineering problem.

  1. Take a straight length of smooth tube.
  2. Make a carrier slightly smaller than the bore.
  3. Fit felt or foam rings at each end so it seals but still slides.
Too tight and friction stops it; too loose and air simply blows past. Real systems used replaceable felt rings for exactly this reason — the seal is a wearing part, and it is the part that decides whether the system works.

اس مرحلے کے لیے مواد:

PVC Pipe (50 mm)PVC Pipe (50 mm)1 length
Cork SheetCork Sheet1 شیٹ
2

Push, then pull

Two ways to make the pressure difference, and they are not equivalent.

  1. Blow into one end with a vacuum cleaner on its blower port and watch the carrier travel.
  2. Now apply suction at the far end instead.
  3. Compare the speed and the smoothness.
Vacuum can only ever produce one atmosphere of difference — about 100 kPa, and in practice much less. Pressure has no such ceiling. Long systems therefore pushed; short ones often sucked, because a suction system leaks inward and stays clean rather than blowing dust out at every joint.

اس مرحلے کے لیے مواد:

Vacuum Pump - 12VVacuum Pump - 12V1 ٹکڑا
3

Measure speed against pressure

Turn it into a measurement.

  1. Mark a measured run length on the tube.
  2. Time the carrier over that distance at several blower settings.
  3. Plot speed against setting.
Speed rises with pressure difference but not proportionally — drag rises steeply with speed, and a longer tube has more wall friction. This is why a network needs booster stations rather than one enormous pump at the middle.

اس مرحلے کے لیے مواد:

StopwatchStopwatch1 ٹکڑا
Steel RulerSteel Ruler1 ٹکڑا
4

Solve the arrival problem

A carrier arriving at 30 km/h has to be stopped without being destroyed.

  1. Send a carrier hard into a bare tube end and inspect the damage.
  2. Add a cushion of trapped air by restricting — not blocking — the exit.
  3. Repeat and compare.
A partly restricted outlet compresses the air ahead of the carrier into a spring that decelerates it. Real terminals used exactly this, plus padded catchers. Blocking the outlet entirely stops the airflow and the carrier stalls short of the station — a nice illustration that the working fluid has to keep moving for the system to work at all.
5

History and context

London, 1853: the first commercial pneumatic despatch line ran a short distance between the Stock Exchange and the Electric Telegraph Company. The idea grew fast because it solved the last-leg problem of telegraphy — a telegram crossed the country in minutes and then waited for a boy with a bicycle.

Paris built the largest network in the world. The poste pneumatique eventually ran to hundreds of kilometres under the city, and a petit bleu — a message on blue paper — could cross Paris in well under an hour. It ran until 1984, outliving the telegram itself.

The scaled-up versions failed. London's Pneumatic Despatch Company built tubes large enough for parcel wagons in the 1860s, and Alfred Ely Beach demonstrated a pneumatic passenger subway under Broadway in 1870. Neither worked economically; sealing a large bore against leakage is very much harder than sealing a small one, and the power required scales badly. Small tubes for documents were the viable size, and remain so.

Still in daily use. Hospitals move blood samples and drugs through pneumatic tubes because a physical sample cannot be emailed, banks use them at drive-through windows, and large factories and supermarkets move cash. A technology that lost to the telephone for messages still wins for objects — and the modern hyperloop proposals are the same push-a-sealed-carrier-through-a-tube idea at a scale that has failed twice before.

مواد

5
Estimated Total
$14.00

CC0 پبلک ڈومین

یہ بلیو پرنٹ CC0 کے تحت جاری کیا گیا ہے۔ آپ اجازت لیے بغیر اس کام کو نقل، ترمیم، تقسیم اور کسی بھی مقصد کے لیے استعمال کرنے کے لیے آزاد ہیں۔

میکر کی حمایت کریں ان کے بلیو پرنٹ کے ذریعے پروڈکٹس خرید کر جہاں وہ میکر کمیشن وینڈرز کی طرف سے مقرر، کماتے ہیں، یا اس بلیو پرنٹ کی نئی تکرار بنائیں اور آمدنی شیئر کرنے کے لیے اسے اپنے بلیو پرنٹ میں کنکشن کے طور پر شامل کریں۔

بحث

(0)

لاگ ان بحث میں شامل ہونے کے لیے

تبصرے لوڈ ہو رہے ہیں...