Reading a Temperature Sensor — SIK Circuit 7

Read temperature from a TMP36 sensor and display Celsius and Fahrenheit readings on the Serial Monitor. Your introduction to serial communication and real-world data.

ہدایات

Parts & Introduction

The TMP36 is an analog temperature sensor that outputs a voltage proportional to temperature. You'll learn to use the Serial Monitor to display real-time readings — an essential debugging tool.

Parts Needed

1x Arduino Uno + USB cable
1x Breadboard
1x TMP36 Temperature Sensor
5x Jumper Wires

Warning: The TMP36 looks similar to the transistor. Look for "TMP" in tiny letters and a triangle logo. The transistor has "222" printed on it. Inserting the wrong component can damage it!

Hardware Hookup

Wiring Instructions

With the TMP36 flat side facing you and pins pointing down, the pins are (left to right): 5V, Signal, GND.

Connect the left pin to 5V.
Connect the middle pin (signal) to Analog Pin A0.
Connect the right pin to GND.

That's it — just 3 wires! The TMP36 can only be connected in one direction. Double-check before powering on.

Arduino Code

Open the Arduino IDE and upload the following sketch to your Arduino board.

temperature_sensor.inoarduino

/*
SparkFun Inventor's Kit
Example sketch 07 — TEMPERATURE SENSOR

Use the serial monitor to read temperature from a TMP36 sensor.

Hardware connections:
  TMP36 (flat side, pins down, left to right): 5V, SIGNAL, GND
  Connect 5V pin to 5V, SIGNAL pin to analog pin 0, GND pin to GND.

This code is completely free for any use.
*/

const int temperaturePin = 0;

void setup()
{
  Serial.begin(9600);
}

void loop()
{
  float voltage, degreesC, degreesF;

  voltage = getVoltage(temperaturePin);

  degreesC = (voltage - 0.5) * 100.0;
  degreesF = degreesC * (9.0/5.0) + 32.0;

  Serial.print("voltage: ");
  Serial.print(voltage);
  Serial.print("  deg C: ");
  Serial.print(degreesC);
  Serial.print("  deg F: ");
  Serial.println(degreesF);

  delay(1000);
}

float getVoltage(int pin)
{
  return (analogRead(pin) * 0.004882814);
  // Converts 0-1023 to 0.0-5.0 volts
}

Test & Experiment

What You Should See

Open the Serial Monitor (magnifying glass icon in Arduino IDE, or Ctrl+Shift+M). You'll see lines updating once per second:

voltage: 0.73  deg C: 23.24  deg F: 73.84

Troubleshooting

Nothing happens: Open the Serial Monitor! The output goes there, not to the LEDs.
Gibberish text: Set the Serial Monitor baud rate dropdown to 9600.
Temperature unchanged: Pinch the sensor with your fingers to warm it up, or apply ice to cool it down.

Experiments to Try

Add an LED that turns on above a temperature threshold (like a heat warning).
Log data over time to see temperature trends.
Combine with the LCD (Circuit 15) to display temperature without a computer.

مواد

•SparkFun Inventor's Kit - V3.2 - 1 kitNOK 999.20
دیکھیں
•Arduino Uno R3 - 1 pieceپلیس ہولڈر
دیکھیں
•Breadboard - 1 pieceپلیس ہولڈر
دیکھیں
•TMP36 Temperature Sensor - 1 pieceپلیس ہولڈر
دیکھیں
•Jumper Wires - 5 piecessNOK 39.20
دیکھیں

درکار اوزار

Computer with Arduino IDE

CC0 پبلک ڈومین

یہ بلیو پرنٹ CC0 کے تحت جاری کیا گیا ہے۔ آپ اجازت لیے بغیر اس کام کو نقل، ترمیم، تقسیم اور کسی بھی مقصد کے لیے استعمال کرنے کے لیے آزاد ہیں۔

میکر کی حمایت کریں ان کے بلیو پرنٹ کے ذریعے پروڈکٹس خرید کر جہاں وہ میکر کمیشن وینڈرز کی طرف سے مقرر، کماتے ہیں، یا اس بلیو پرنٹ کی نئی تکرار بنائیں اور آمدنی شیئر کرنے کے لیے اسے اپنے بلیو پرنٹ میں کنکشن کے طور پر شامل کریں۔

بحث

(0)

لاگ ان بحث میں شامل ہونے کے لیے

تبصرے لوڈ ہو رہے ہیں...