فن
خوبصورتی اور تندرستی
دستکاری
ثقافت اور تاریخ
تفریح
ماحول
خوراک اور مشروبات
ریورس انجینئرنگ
سائنسز
کھیل
ٹیکنالوجی
پہننے والے آلات
The Cam-Lever Lemon Squeezer: A Cam on a Shaft Presses the Plunger, Springs Lift It
Martin

تخلیق کار

Martin

30. ستمبر 2026NO
42
0
0
0
0

The Cam-Lever Lemon Squeezer: A Cam on a Shaft Presses the Plunger, Springs Lift It

A plunger pressed straight down by the hand needs a strong push to empty a lemon. A. Clarence Weeks of New York received US 165,638, dated 13 July 1875, for a squeezer with a frame on legs over a dish, a perforated bowl in the frame, a plate hinged to one end carrying the plunger, two standards on the frame with a shaft across them carrying "a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger", and springs from the plate to the standards. "By the use of the cam-lever an immense power is obtained, and the juice is extracted from the lemon in a more thorough and perfect manner than when the power is applied directly to the plate or bar carrying the plunger." This rung works out the cam's average force, with a work check, then builds the frame, the hinged plate and the cam lever in hardwood and steel, and squeezes lemons with it.
درمیانہ
About 5 hours

ہدایات

1

The cam's force

Jupyter نوٹ بک لوڈ ہو رہی ہے…
2

A lever press before it

The embedded blueprint presses the lemon with the lever itself. Weeks puts a cam lever over a hinged plate, so a turn of the lever gives a far greater push.
3

Read US 165,638

"Two standards, E E, are attached to the frame A, one on each side, in the upper portions of which standards are bearings for a shaft, f, to which is attached, midway of its length, a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger. J is a spring, which may be of rubber or metal, having its lower end attached to the board or plate C, and its upper end attached to the standard E." "When the cam-lever G is depressed its face or bearing-surface presses upon the board or plate C, and forces the plunger into the bowl upon the lemon."
4

Build the squeezer and press lemons

**Frame and bowl.** Make a hardwood board frame on four legs, tall enough for a dish beneath, with a hole in it. Fit a tin-can bowl with a punched base into the hole. **Plate and plunger.** Hinge a hardwood plate to one end of the frame with a butt hinge, and screw a hardwood plunger to its underside so it enters the bowl. **Standards and cam.** Screw two hardwood standards to the frame's sides beside the plate and run a steel rod across between them as the shaft f. Cut a hardwood cam lever with a curved face whose distance from the shaft grows by about 15 mm over 60° of turn, drill it for the shaft, and fix it in the middle of the rod with a pin. **Springs.** Hook two extension springs from the plate to the standards so they lift the plate when the cam is raised. **Test.** Put a half lemon in the bowl over a dish and press the lever down. Compare the juice with a half pressed by pushing the plate down by hand.

اس مرحلے کے لیے مواد:

سخت لکڑی کا تختہسخت لکڑی کا تختہ2 ٹکڑے
سخت لکڑی کا ٹکڑاسخت لکڑی کا ٹکڑا2 ٹکڑے
لکڑی کی چوبی کیللکڑی کی چوبی کیل0.6 میٹر
لکڑی کے پیچلکڑی کے پیچ16 ٹکڑے
لکڑی کا گوندلکڑی کا گوند1 ٹکڑا
ٹین کا ڈبہٹین کا ڈبہ1 ٹکڑا
دروازے کا قبضہدروازے کا قبضہ1 ٹکڑا
نرم فولاد کی گول سلاخنرم فولاد کی گول سلاخ0.2 میٹر
کیلیںکیلیں2 ٹکڑے
کھنچاؤ کی کمانیکھنچاؤ کی کمانی2 ٹکڑے
لیموںلیموں3 ٹکڑے

درکار اوزار:

ہاتھ کی آریہاتھ کی آری
لکڑی کی رنداں کا سیٹلکڑی کی رنداں کا سیٹ
موٹی ریتیموٹی ریتی
بے تار مشقبے تار مشق
مشقوں کا سیٹمشقوں کا سیٹ
چادر کاٹنے کی قینچیچادر کاٹنے کی قینچی
ہتھوڑاہتھوڑا
پیچ کس سیٹپیچ کس سیٹ
لوہا کاٹنے کی آریلوہا کاٹنے کی آری
باورچی خانے کی چھریباورچی خانے کی چھری
ڈیجیٹل باورچی خانہ ترازوڈیجیٹل باورچی خانہ ترازو
چمڑے کے کام کے دستانےچمڑے کے کام کے دستانے
5

A cam that slips, jams or does not lift

Cam-lever lemon squeezer troubleshooting.

Flow

Loading...
6

History and honest limits

**A. Clarence Weeks** of New York, New York, filed US 165,638 on 26 April 1875; it is dated 13 July 1875. His frame A had feet or legs a, the bowl B had perforations b, the plate C was hinged to one end of the frame, and there could be one spring or two. His claim is the frame with the perforated bowl and standards, the pivoted plate with its plunger, the springs, and the shaft with its cam lever. **Honest limits.** Hardwood, a tin bowl and a steel rod stand in for his parts. The notebook gives the average force without friction; its forces, lengths and angles are examples. Your juice is the result.

مواد

11

درکار اوزار

12

CC0 پبلک ڈومین

یہ بلیو پرنٹ CC0 کے تحت جاری کیا گیا ہے۔ آپ اجازت لیے بغیر اس کام کو نقل، ترمیم، تقسیم اور کسی بھی مقصد کے لیے استعمال کرنے کے لیے آزاد ہیں۔

میکر کی حمایت کریں ان کے بلیو پرنٹ کے ذریعے پروڈکٹس خرید کر جہاں وہ میکر کمیشن وینڈرز کی طرف سے مقرر، کماتے ہیں، یا اس بلیو پرنٹ کی نئی تکرار بنائیں اور آمدنی شیئر کرنے کے لیے اسے اپنے بلیو پرنٹ میں کنکشن کے طور پر شامل کریں۔

بحث

(0)

لاگ ان بحث میں شامل ہونے کے لیے

تبصرے لوڈ ہو رہے ہیں...