فن
خوبصورتی اور تندرستی
دستکاری
ثقافت اور تاریخ
تفریح
ماحول
خوراک اور مشروبات
ریورس انجینئرنگ
سائنسز
کھیل
ٹیکنالوجی
پہننے والے آلات
The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles
Woody

تخلیق کار

Woody

6. اکتوبر 2026NO
28
0
0
0
0

The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles

Water dribbled onto the back of a brush stays in the bristles and never reaches the surface being washed. Frank L. Brinn of Milwaukee received US 840,604, patented 8 January 1907, for a fountain brush in which "the fluid may be delivered to the longitudinal central portion of the brush in a sheet, which when the fluid is turned on at full head will serve to separate the bristles and flush the surface to be washed": slots through the block narrow toward the bristles, fed from a cylinder on top through a tubular handle, with a cup on the handle to catch what runs down. This rung works out how the taper speeds the sheet, then cuts the slots in a scrub brush, plumbs it and compares full flow with throttled flow.
درمیانہ
About 4 hours

ہدایات

1

Sheet speed from the slot

Jupyter نوٹ بک لوڈ ہو رہی ہے…
2

Water through a brush's back before it

The embedded blueprint jets or soaks water through openings in a brush's back. Brinn shapes the openings into tapered slots so the water leaves as a sheet.
3

Read US 840,604

"By opening the valve at 3 to its full capacity a sheet of water will be discharged which will separate the bristles and effectively flush the surface to be washed, whether the bristles are in contact with such surface or not. By partially closing the valve at 3 the sheets of water escaping through the openings 18 are broken up by the bristles, and the water thus becomes distributed throughout the brush."
4

Cut the slots

On the scrub brush's top mark two slots 60 × 8 mm, 90 mm apart on the centre line. Drill a row of holes in each and cut it through with the coping saw.

اس مرحلے کے لیے مواد:

رگڑنے کا برشرگڑنے کا برش1 ٹکڑا

درکار اوزار:

میز کا شکنجہمیز کا شکنجہ
بے تار مشقبے تار مشق
مشقوں کا سیٹمشقوں کا سیٹ
گھما دار آریگھما دار آری
پکی سیاہی کا مارکرپکی سیاہی کا مارکر
پیمانہپیمانہ
5

Taper the slots

Pare each slot with chisels so its long sides close to about 1.5 mm at the bristle face and its ends open out to 70 mm. Trim the bristles along the slot line.

درکار اوزار:

لکڑی کی رنداں کا سیٹلکڑی کی رنداں کا سیٹ
ہتھوڑاہتھوڑا
ڈیجیٹل ورنیئر کیلیپر ۶ انچڈیجیٹل ورنیئر کیلیپر ۶ انچ
دستکاری کا چاقودستکاری کا چاقو
6

Make the manifold

Cut 160 mm of 22 mm copper tube and cap both ends with fittings. File a 4 mm slot along its underside over both brush slots. Fit a tee in its middle for the handle.

اس مرحلے کے لیے مواد:

تانبے کی نلکیتانبے کی نلکی1 ٹکڑا
پیتل کے جوڑپیتل کے جوڑ1 ٹکڑا

درکار اوزار:

نلی کاٹنے کا اوزارنلی کاٹنے کا اوزار
ریتیاں (ہاتھ کی ریتی)ریتیاں (ہاتھ کی ریتی)
انگریزی پاناانگریزی پانا
7

Seat the manifold

Bed the manifold on the brush in silicone over a rubber gasket and strap it down with an aluminium strip and four wood screws.

اس مرحلے کے لیے مواد:

سلیکون سیلنٹسلیکون سیلنٹ1 ٹکڑا
ربڑ کی چادرربڑ کی چادر1 ٹکڑا
ایلومینیم کی چادرایلومینیم کی چادر1 ٹکڑا
لکڑی کا پیچ #8 × ۱ انچلکڑی کا پیچ #8 × ۱ انچ1 ٹکڑا

درکار اوزار:

چادر کاٹنے کی قینچیچادر کاٹنے کی قینچی
پیچ کس سیٹپیچ کس سیٹ
دستکاری کا چاقودستکاری کا چاقو
8

Handle, valve and drip cup

Fit 1.2 m of 15 mm copper tube to the tee, with a ball valve and hose connector at its top. Slide a small tin can, holed and sealed with silicone, onto the handle as a drip cup, and fit a short copper spout low on its side.

اس مرحلے کے لیے مواد:

تانبے کی نلکیتانبے کی نلکی1 ٹکڑا
گیند والا والوگیند والا والو1 ٹکڑا
پیتل کے جوڑپیتل کے جوڑ1 ٹکڑا
PTFE چوڑی بند کرنے کا فیتہPTFE چوڑی بند کرنے کا فیتہ1 ٹکڑا
ٹین کا ڈبہٹین کا ڈبہ1 ٹکڑا
سلیکون سیلنٹسلیکون سیلنٹ1 ٹکڑا

درکار اوزار:

نلی کاٹنے کا اوزارنلی کاٹنے کا اوزار
انگریزی پاناانگریزی پانا
بے تار مشقبے تار مشق
مشقوں کا سیٹمشقوں کا سیٹ
9

The patent drawing

US 840,604 drawing sheet, public domain (expired patent).
قدم 9 - Image 1
10

Full flow against throttled

Connect the garden hose. With the valve fully open, hold the brush 2 cm off a board and watch the sheet part the bristles; then close it half and watch the water spread through them. Time a litre into the jug each way.
قدم 10 - Image 1

اس مرحلے کے لیے مواد:

پانیپانی1 ٹکڑا

درکار اوزار:

پیمائشی جگپیمائشی جگ
اسٹاپ واچاسٹاپ واچ
پیمانہپیمانہ
باغ کا پائپباغ کا پائپ
11

A sheet that sprays, sputters or leaks

Sheet-of-water fountain brush troubleshooting.

Flow

Loading...
12

History and honest limits

**Frank L. Brinn**, a citizen of Canada residing in Milwaukee, filed US 840,604 on 20 February 1905; it was patented 8 January 1907. His cylinder is held to the block by a plate with packing and screws, its slots feeding the slot-apertures; the handle's end carries a rubber sheath and the valve; the cup, with its spout, collects the water instead of letting it run down the handle when the brush is raised. **Honest limits.** A slotted copper tube stands in for his cylinder, and a tin can for his cup. The notebook treats the sheet as uniform. What you see on the board is the result.

مواد

11

درکار اوزار

18

CC0 پبلک ڈومین

یہ بلیو پرنٹ CC0 کے تحت جاری کیا گیا ہے۔ آپ اجازت لیے بغیر اس کام کو نقل، ترمیم، تقسیم اور کسی بھی مقصد کے لیے استعمال کرنے کے لیے آزاد ہیں۔

میکر کی حمایت کریں ان کے بلیو پرنٹ کے ذریعے پروڈکٹس خرید کر جہاں وہ میکر کمیشن وینڈرز کی طرف سے مقرر، کماتے ہیں، یا اس بلیو پرنٹ کی نئی تکرار بنائیں اور آمدنی شیئر کرنے کے لیے اسے اپنے بلیو پرنٹ میں کنکشن کے طور پر شامل کریں۔

بحث

(0)

لاگ ان بحث میں شامل ہونے کے لیے

تبصرے لوڈ ہو رہے ہیں...