فن
خوبصورتی اور تندرستی
دستکاری
ثقافت اور تاریخ
تفریح
ماحول
خوراک اور مشروبات
ریورس انجینئرنگ
سائنسز
کھیل
ٹیکنالوجی
پہننے والے آلات
Twist, Cup and Bow: Winding Sticks Make the Invisible Obvious
A board can be out of true in three separate ways, and they need three different tests. BOW is a curve along its length, CUP is a curve across its width, and TWIST — wind — is the two ends being in different planes.
Twist is the one that matters most and the one you cannot see. A board can look perfectly flat, sit on the bench without rocking, and still be twisted enough to make a door that will not close.
Winding sticks solve it with no measurement at all: two straight battens and your eye, amplifying a fraction of a millimetre into something unmistakable.
درمیانہ
3 hours
ہدایات
1
1
Bow and cup: a straightedge finds both
Bow and cup: a straightedge finds both
Lay a straightedge along the length of the board and look for light under it: that is BOW. Lay it across the width and do the same: that is CUP.
Check in several places along and across, because a board is rarely uniform. Cup usually goes the same way on a flat-sawn board — away from the heart of the tree — which is why boards are often alternated in a glued panel.
Both are straightforward to see and straightforward to plane out, and both cost thickness. Take the measurement before deciding the finished thickness, or you will find the board is thinner than the design needs after truing it.
اس مرحلے کے لیے مواد:
سخت لکڑی کا تختہ1 ٹکڑادرکار اوزار:
سیدھا کنارہ
پیمانہ
رندہ2
2
Winding sticks: how the trick actually works
Winding sticks: how the trick actually works
Stand one stick across the board at each end and sight across their top edges from a low angle. If the board is flat, the two top edges line up as a single line. If it is twisted, one stick appears tilted relative to the other.
The sticks amplify. They are much wider than the board is thick, so an end-to-end twist of a fraction of a millimetre becomes a visible several-millimetre offset between the two far corners — a difference you can see easily and could never feel.
Make them from any straight stable stock, in a matched pair, dead parallel along their length. A dark inlay or a painted stripe along the top edge of one makes the sighting much easier, which is why traditional pairs have contrasting inlays.
اس مرحلے کے لیے مواد:
سخت لکڑی کا تختہ2 ٹکڑےدرکار اوزار:
بل جانچنے کی جوڑی پٹیاںسیدھا کنارہ3
3
How much a small twist actually costs
How much a small twist actually costs
Jupyter نوٹ بک لوڈ ہو رہی ہے…
درکار اوزار:
بل جانچنے کی جوڑی پٹیاں
حساب کرنے والا آلہ4
4
Take the high corners down, and re-check constantly
Take the high corners down, and re-check constantly
Twist is removed by planing the two diagonally opposite HIGH corners down until the sticks read parallel. Mark the high corners in pencil while the sticks are still in place so you know which they are once you pick up the plane.
Work diagonally across the board rather than along it — the high corners are on a diagonal, so that is the direction the shavings need to come from. Check again every few strokes. It is easy to overshoot and put a twist the other way in.
Then re-check with the straightedge for bow and cup, because removing twist changes them. True the face completely before touching the edge; a face that goes out of true afterwards takes the edge's squareness with it.
اس مرحلے کے لیے مواد:
سخت لکڑی کا تختہ1 ٹکڑادرکار اوزار:
بل جانچنے کی جوڑی پٹیاںرندہسیدھا کنارہمتعلقہ بلیو پرنٹ
یہ بلیو پرنٹ علم بانٹتے ہیں — تکنیک، مواد یا اصول
CC0 پبلک ڈومین
یہ بلیو پرنٹ CC0 کے تحت جاری کیا گیا ہے۔ آپ اجازت لیے بغیر اس کام کو نقل، ترمیم، تقسیم اور کسی بھی مقصد کے لیے استعمال کرنے کے لیے آزاد ہیں۔
میکر کی حمایت کریں ان کے بلیو پرنٹ کے ذریعے پروڈکٹس خرید کر جہاں وہ میکر کمیشن وینڈرز کی طرف سے مقرر، کماتے ہیں، یا اس بلیو پرنٹ کی نئی تکرار بنائیں اور آمدنی شیئر کرنے کے لیے اسے اپنے بلیو پرنٹ میں کنکشن کے طور پر شامل کریں۔