Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Air Compressor: Twin Pump-Cylinder, Water-Cooled (Shop Notes, 1912)
A simple compressor that fills a tank to about 50 lb: two bought cast-iron well-pump cylinders, 2 1/2 in bore, driven alternately by a rocking arm from a crank, with check valves in and out and a water jacket pipe to cool them.
Source: Popular Mechanics Shop Notes for 1912, pp. 1708-1709. Unknown: tank, pipe sizes. Picture: Figs. 1-2 of the book.
Średniozaawansowany
Unknown
Instrukcje
1
1
Pipe the two cylinders
Pipe the two cylinders
Take two ordinary cast-iron open-well pump cylinders, 2 1/2 in bore, bought complete with guide rods and plungers. Join their open ends with tees to a cross pipe C, and fit a packing box from an old valve (A, B) into each tee so the plunger rods D and E pass through (Fig. 1).
Materiały do tego kroku:
Nieznany metal2 pump cylinders with plungers
Rura stalowa (grubościenna, z gwintowanymi końcami)1 pipe C
Złączka gwintowana do rur2 tees
Nieznana uszczelka2 packing boxesPotrzebne narzędzia:
Klucz hydrauliczny2
2
Fit the valves
Fit the valves
On the outer end of each cylinder fit an inlet check valve (H, I) and an outlet valve (J, K), the outlets joined to pipe L running to the tank.
Materiały do tego kroku:
Zawór zwrotny4 H, I, J, K
Rura stalowa (grubościenna, z gwintowanymi końcami)1 pipe L
Złączka gwintowana do rur1 sztuka
Nieznany materiał1 air tankPotrzebne narzędzia:
Klucz hydrauliczny3
3
Water-cool it
Water-cool it
Run cooling water through pipe C, set by valve M in and valve N out, so there is no pressure on the water to push it into the air chambers O and P.
Materiały do tego kroku:
Zawór grzybkowy2 M and NPotrzebne narzędzia:
Woda
Klucz hydrauliczny4
4
Fit the crank drive
Fit the crank drive
Drive it from a shaft (Fig. 2): crank S works an arm pivoted at its centre T, and the plunger rods D and E attach to the arm's ends U and V.
Materiały do tego kroku:
Nieznany metal1 crank, arm
Śruba z łbem sześciokątnym - klasa 8.81 pivot and rod pins, number not givenPotrzebne narzędzia:
Wiertarka ręczna
Klucz nastawnyMateriały
8- 1 crank, armZastępnik
- Zastępnik
- 1 sztukaZastępnik
- 2 packing boxesZastępnik
- 4 H, I, J, KZastępnik
- 1 air tankZastępnik
- 2 M and NZastępnik
- 1 pivot and rod pins, number not givenZastępnik
Według tego planu powstaje
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.
