Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Air Thermometer: Blackened Tin Box and Water U-Tube (Boy Mechanic, 1913)
Penny

Autor

Penny

14. listopad 2026DK
8
0
0
0
0

Air Thermometer: Blackened Tin Box and Water U-Tube (Boy Mechanic, 1913)

A sensitive air thermometer: a small sealed tin box, blackened on its face, breathes through a brass tube into a bent glass U-tube holding a little water; warmth on the box expands the air and pushes the water up the scale.
Średniozaawansowany
Two hours

Instrukcje

1

Read the Boy Mechanic

"This instrument will measure the amount of heat given by a candle some 20 or 30 ft. away."
2

Seal the box

Take a small tin box about 1-1/4 in deep and 2 in across. Solder a 1 in piece of 1/4 in brass tube into its side, then solder the cover on so air can only escape through the tube.

Materiały do tego kroku:

Puszka blaszanaPuszka blaszana1 sztuka
Rura mosiężnaRura mosiężna1 sztuka
Lut cynowo-ołowiowyLut cynowo-ołowiowy1 sztuka

Potrzebne narzędzia:

LutownicaLutownica
Wiertarka ręcznaWiertarka ręczna
3

Bend the glass tube

Take 1/4 in glass tube at least 18 in long and bend it into a U as in the figure by holding it across a broad flame until it sags under its own weight. Join it to the brass tube with a short rubber hose, bound with fine copper wire if loose.

Materiały do tego kroku:

Rurka szklanaRurka szklana1 sztuka
Wąż gumowyWąż gumowy1 sztuka
Drut miedzianyDrut miedziany1 sztuka

Potrzebne narzędzia:

Palnik spirytusowyPalnik spirytusowy
4

Stand and base

Make the standard from No. 10 wire about 10 in long on an oak base, with a No. 14 wire soldered across it and bent round the brass tube and the glass tube.

Materiały do tego kroku:

Drut żelaznyDrut żelazny1 sztuka
Deska z dębu białegoDeska z dębu białego1 sztuka
Lut cynowo-ołowiowyLut cynowo-ołowiowy1 sztuka

Potrzebne narzędzia:

Szczypce płaskieSzczypce płaskie
LutownicaLutownica
Świder korbowy z wiertłemŚwider korbowy z wiertłem
5

Blacken and fill

Smoke the bottom of the box black over a little burning cotton soaked in turpentine (after any painting of the rest). Put water in the U-tube with a dropper and paint a scale on the glass.

Materiały do tego kroku:

Czerń lampowaCzerń lampowa1 sztuka
Czarna farbaCzarna farba1 sztuka
Woda destylowanaWoda destylowana1 sztuka
6

Troubleshooting

Air thermometer troubleshooting.

Flow

Loading...
7

History and honest limits

From **The Boy Mechanic, Book 1** (Popular Mechanics, 1913), pp. 152-153, by J. Thos. Rhamstine (checked on the archive.org scan boymechanic0000unse_n5a8). It shows relative warmth, not degrees. He also mentions etching the scale with hydrofluoric acid; we use paint only. The spirit lamp in place of a gas jet is ours.

Materiały

11

Wymagane narzędzia

5

Według tego planu powstaje

Powiązane blueprinty

Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...