Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Angle Grinder: Reversible, with a Hollow Arbour and a Top Arbour Lock (Turley, US 5,718,621)
Forge

Autor

Forge

9. listopad 2026NO
7
0
0
0
0

Angle Grinder: Reversible, with a Hollow Arbour and a Top Arbour Lock (Turley, US 5,718,621)

An angle grinder spins a disc at right angles to its motor: a bevel gear on the motor shaft turns a bevel gear on an upright arbour. E. M. Turley (US 5,718,621, 1998) makes the arbour hollow. A bolt runs down through it into a hexagonal coupling piece that drives the disc and clamps it against the arbour's flange, so the motor can run either way without loosening the disc. To change the disc, a sliding lock piece on top locks the arbour, opens a hole over the bolt head and switches the motor off in one move. Source: E. M. Turley, "Reversible Angle Grinder with Top Arbour Lock", US Patent 5,718,621 (filed 1996, granted 1998). Picture: its Fig. 1.
Zaawansowany
Unknown

Instrukcje

1

Read Turley

"The angle grinder according to the preferred embodiment of the invention includes a reversible motor driving a hollow arbour via a right angle bevel gear arrangement. The arbour has a right angle flange at its bottom. The flange abuts against one side of the disk tool."
2

Turn the hollow arbour

Turn an arbour hollow all through, with three outside shoulders (lower, middle and upper) for the two bearings and the bevel gear, and grooves above each for a snap ring. At the bottom, enlarge the bore into a hexagonal recess ending in a right-angle flange. At the top, enlarge the bore so the bolt head sits below the rim, and cut four equally spaced square notches (crenellations) in the rim. Sizes and metal are not given.

Materiały do tego kroku:

Nieznany metalNieznany metal1 arbour

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
FrezarkaFrezarka
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Nieznane wymiaryNieznane wymiary
3

Make the coupling piece and bolt

Make a coupling piece: a hexagonal upper part that fits the arbour's recess, a round pilot that fits the standard centre hole of commercial grinding discs, and a right-angle flange at its base. Bore and tap it from the top, closed at the bottom. Make a retaining bolt long enough to run from the arbour's top down into the coupling piece, threaded at its lower end (Fig. 1 draws a socket in its head).

Materiały do tego kroku:

Nieznany metalNieznany metal1 coupling piece
Nieznany metalNieznany metal1 retaining bolt

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
FrezarkaFrezarka
Zestaw do gwintowaniaZestaw do gwintowania
Nieznane wymiaryNieznane wymiary
4

Cut the bevel gears

Cut two bevel gears with teeth at forty-five degrees (equal gears for a right-angle drive): one fixed on the arbour against its middle shoulder, one on the front end of the motor shaft. Tooth count and metal are not given.

Materiały do tego kroku:

Nieznany metalNieznany metal2 bevel gears

Potrzebne narzędzia:

FrezarkaFrezarka
Frez do kół stożkowychFrez do kół stożkowych
Nieznane wymiaryNieznane wymiary
5

Assemble the drive

Mount a reversible electric motor in the housing, its shaft running back in a rear bearing and forward in a front bearing, the bevel gear on its front end. Set the arbour upright in two bearings at its lower and upper shoulders, the bevel gears meshing, with snap rings above the bearings and the gear. Drop the bolt down the arbour on a lock washer, fit the coupling piece from below and screw it on. Motor rating, housing material and how the bearings are held are not given.

Materiały do tego kroku:

Silnik elektrycznySilnik elektryczny1 reversible
Łożysko kulkoweŁożysko kulkowe4 sztuk
Nieznany materiałNieznany materiał1 housing

Potrzebne narzędzia:

Zestaw kluczy imbusowychZestaw kluczy imbusowych
Nieznana metoda kształtowaniaNieznana metoda kształtowania
Nieznane wymiaryNieznane wymiary
6

Fit the arbour lock

Make a rectangular lock piece that slides in the housing top across the arbour head, with a lever up through a slot in the housing, a tool hole, and a square tang underneath that drops into a rim notch. A spring on its front face holds it back in the running position. Fix a two-contact power switch to its rear so the motor circuit is broken when the piece is slid into the locking position. Cut a hole in the housing top over the bolt head and a slot for the lever.

Materiały do tego kroku:

Nieznany metalNieznany metal1 lock piece
SprężynaSprężyna1 sztuka
Wyłącznik zasilaniaWyłącznik zasilania1 sztuka

Potrzebne narzędzia:

FrezarkaFrezarka
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
7

Change a disc

Push the lever forward: the tang locks the arbour, the switch cuts the motor and the tool hole sits over the bolt head. Unscrew the bolt from above with the key and pull the coupling piece; put the new disc on its pilot and screw it back up tight, so the disc is clamped between the arbour flange and the coupling flange. Let the lever spring back to run. Turley: a loose bolt cannot drop the disc, which rattles to warn you to tighten it.

Potrzebne narzędzia:

Zestaw kluczy imbusowychZestaw kluczy imbusowych

Materiały

6

Wymagane narzędzia

10

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...