Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)
Woody

Autor

Woody

4. listopad 2026NO
11
0
0
0
0

Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)

A shop belt sander for dressing wood surfaces: a 6 in garnet-paper belt running over four crowned wooden pulleys, one driven by the lathe, pressed down onto the work with a hand float. Best belt speed about 2,500 ft per minute; leave about 1 in between work and belt. Source: Popular Mechanics Shop Notes for 1919, p. 3235. Picture: the article's drawing.
Średniozaawansowany
Unknown

Instrukcje

1

Turn the pulleys

Build up four solid wood pulleys 10 in across with 8 in faces and turn them in the lathe with a very slight crown; too much crown harms the belt.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego4 built-up pulleys

Potrzebne narzędzia:

Tokarka do drewnaTokarka do drewna
2

Mount the pulleys

Mount one pulley on a firmly held arbor in the lathe and the other three on iron-pipe shafts on a frame (drawing). Turn and file a true journal on each pipe, pour babbitt bushings in the pulleys, and cut oil grooves in the pipe or babbitt. Supporting the shafts on one side lets the belt slip off; supporting both sides is stronger.

Materiały do tego kroku:

Rura stalowa (grubościenna, z gwintowanymi końcami)Rura stalowa (grubościenna, z gwintowanymi końcami)3 shafts
Nieznany metalNieznany metal1 babbitt bushings
Tarcica sosnowaTarcica sosnowa1 frame

Potrzebne narzędzia:

Pilnik do metaluPilnik do metalu
Cedzak dziurkowanyCedzak dziurkowany
Piła ręcznaPiła ręczna
MłotekMłotek
3

Make the belt

Cut 6 in garnet paper (No. 1 1/2 for general work) so the ends just meet over the pulleys. Glue the smooth side at the joint, splice it with a strip of cloth about 1 in wide and then one about 3 in wide, cover each side with paper, and clamp between two small boards.

Materiały do tego kroku:

Papier ściernyPapier ścierny1 6 in garnet paper
Tkanina bawełnianaTkanina bawełniana1 sztuka
Klej zwierzęcyKlej zwierzęcy1 sztuka

Potrzebne narzędzia:

Ścisk typu CŚcisk typu C
4

Set up and run

Run the belt at about 2,500 ft per minute using the lathe's cone pulley. Set the work about 1 in below the belt on a table or a low sliding platform (two sets of tongue-and-groove joints at right angles), start the machine and press the belt down with a float like a blackboard eraser, or a roller.

Materiały do tego kroku:

Tarcica sosnowaTarcica sosnowa1 platform, float

Potrzebne narzędzia:

Tokarka do drewnaTokarka do drewna

Materiały

7

Wymagane narzędzia

6

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...