Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Knock-Down Footstool: Bolted Metal Legs and Rails Under a Screwed-On Wooden Top (Bolens, 1900)
Forge

Autor

Forge

13. listopad 2026NO
7
0
0
0
0

Knock-Down Footstool: Bolted Metal Legs and Rails Under a Screwed-On Wooden Top (Bolens, 1900)

Harry W. Bolens of Port Washington, Wisconsin, received US 640,265, dated 2 January 1900, for a footstool whose base comes apart: four metal corner legs and four rails bolted together, with a wooden top screwed on through lugs on the legs. It packs flat for storage and shipping. His legs were ornamental castings; ours are bent from steel angle. All sizes are ours.
Początkujący
About 4 hours

Instrukcje

1

Cut list

Wczytywanie notatnika Jupyter…
2

Read US 640,265

"The above-described base has the advantage of being a knockdown structure, and thus I provide for economical storage and transportation."
3

Make the legs

Cut four legs of steel angle to the notebook's length, his corner legs A. At the top of each, cut and bend a small tab inward to make the flange and lug (his b and c), and drill the lug for a top screw. File off sharp edges.

Materiały do tego kroku:

Kątownik ze stali miękkiejKątownik ze stali miękkiej1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Imadło warsztatoweImadło warsztatowe
Młotek ślusarski z kulistym rąbemMłotek ślusarski z kulistym rąbem
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Zestaw pilnikówZestaw pilników
4

Make the rails

Cut two side rails and two end rails of flat bar, his rails B. Bend each end slightly (his offset ends) so it lies flush inside the leg's angle. Drill matching holes through rail ends and legs.

Materiały do tego kroku:

Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Imadło warsztatoweImadło warsztatowe
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
5

Bolt the base

Bolt each rail end to its leg with a bolt and nut, his bolts f and nuts g. Check the base stands square and level.

Materiały do tego kroku:

Zestaw śrub sześciokątnychZestaw śrub sześciokątnych1 sztuka

Potrzebne narzędzia:

Klucz nastawnyKlucz nastawny
6

Fit the top

Cut and sand a hardwood top, his top C. Set it on the base and drive a screw up through each leg's lug into it, his screws h. Upholster it if you like, as he allows.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Wkręty do drewnaWkręty do drewna1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Papier ściernyPapier ścierny
Zestaw wkrętakówZestaw wkrętaków
7

Troubleshooting

Footstool troubleshooting.

Flow

Loading...
8

History and honest limits

**Harry W. Bolens** of Port Washington, Wisconsin, US 640,265, dated 2 January 1900, filed 4 October 1899. He claimed "a footstool-base consisting of legs provided at their upper ends with inwardly-extending flanges as well as horizontal lugs ... apertured for the engagement of top securing devices" and rails between the flanges. His legs and rails were castings, though he does not limit the material; the steel angle and flat bar, the bent lugs, the hardwood top and all sizes are ours.

Materiały

5

Wymagane narzędzia

10

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...