Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Boring Bar: Driven Between Centres, with a Set-Screw Cutter (Yates, 1922)
A home-made boring bar for holes too long for an ordinary boring tool, which would spring. A short, stiff bar runs between the lathe centres, driven by a dog, and carries a hardened tool-steel cutter locked in a cross-hole by a set screw. The work is bolted to the lathe carriage and fed past the turning cutter.
Result: a boring bar, plus the small short-cut bar of Fig. 110.
Source: R. F. Yates, Lathe Work for Beginners (1922), pp. 134-136. Unknown: bar diameter and set-screw size. Picture: Figs. 110-111 of the book.
Średniozaawansowany
Unknown
Instrukcje
1
1
Turn the bar
Turn the bar
Turn a bar no longer than the job needs; the shorter it is, the less it twists under the cut. Drill both ends for the lathe centres. For short cuts, the small bar of Fig. 110 is 4 to 6 inches long with a round shank and a squared end. Ours: mild steel round bar. Not given: the diameter.
Materiały do tego kroku:
Pręt okrągły ze stali niskowęglowej1 boring barPotrzebne narzędzia:
Tokarka do metalu
Nieznane wymiary2
2
Fit the cutter and set screw
Fit the cutter and set screw
Drill a cross-hole through the bar for the cutter and drill and tap a hole into it for a set screw that locks the cutter. Make the cutter of tool steel, grind its point with proper clearance, and harden it.
Materiały do tego kroku:
Pręt kwadratowy ze stali narzędziowej1 cutter
Nieznany metal1 set screwPotrzebne narzędzia:
Wiertarka stołowa
Zestaw do gwintowania
Toczydło
Piec do obróbki cieplnej
Kadź hartownicza3
3
Bore with it
Bore with it
Bolt the work down to the lathe carriage carefully and securely; carriage bolts of several sizes are handy for this. Drive the bar between centres with a dog and feed the carriage. Run very slowly when boring cast iron, and keep the feed light so the bar does not spring.
Potrzebne narzędzia:
Tokarka do metalu
Śruba zamkowaMateriały
3- 1 boring barZastępnik
- Zastępnik
- 1 set screwZastępnik
Wymagane narzędzia
8- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Materiały z połączonych planów

10% atrybucji
Mild Steel Bar Stock Forged from an Ingot
autor: Forge
Nowoczesny
45
0
0
0
5
0

10% atrybucji
Tool-Steel Bar: Crucible Steel Drawn Out at a Cherry-Red Heat
autor: Forge
Kowal
33
0
0
0
5
0

10% atrybucji
Lathe Cutting Tool: Ground to the Clearance and Slope for Each Metal (Machinery's Handbook, 1924)
autor: Forge
Narzędzia do obróbki metali
12
0
0
0
1
0
Według tego planu powstaje
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.
