Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Jointed Fishing Rods: Two- and Three-Piece Casting, Trout and Bass Fly, Salt-Water and Tarpon Rods (Boy Mechanic, 1915)
Woody

Autor

Woody

13. listopad 2026NO
7
0
0
0
0

Jointed Fishing Rods: Two- and Three-Piece Casting, Trout and Bass Fly, Salt-Water and Tarpon Rods (Boy Mechanic, 1915)

Part II of Stillman Taylor's rod-making series (The Boy Mechanic, Book 2, 1915): once the one-piece casting rod is mastered, the same planing, grasp and finishing methods make jointed rods. He gives full caliper tables and fitting lists for six rods; choose one in the notebook. Sections join with welted, shouldered ferrules, and every rod gets two tips "in view of a possible breakage".
Zaawansowany
About 2-3 weeks (glue and varnish drying)

Instrukcje

1

His caliper tables

Wczytywanie notatnika Jupyter…
2

Read The Boy Mechanic, Book 2

"While the action of the one-piece rod is undeniably better than when the rod is made in two or three pieces, it is less compact to carry." He warns that "the more joints incorporated in a rod, the less satisfactory it will be from an angling standpoint", since ferrules cannot follow the rod's curve.
3

Choose the rod and get the stock

Pick a rod from the notebook. Stock (dagame or greenheart): two-piece casting -- butt 5/8 in x 3 ft, two tips 3/8 in x 3 ft; three-piece casting -- all 2 ft, butt 5/8 in, joint and tips 3/8 in; trout or bass fly -- butt 5/8 in x 4 ft, joint and tips 3/8 in x 4 ft; salt-water -- both 4 ft, butt 3/4 in, tip 1/2 in; tarpon -- one piece 1 in x 6-1/2 ft.

Materiały do tego kroku:

Drewno dagameDrewno dagame4 sztuk

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Miara zwijanaMiara zwijana
4

Plane each section to its table

Plane, round and scrape each section exactly as for the one-piece rod, calipering at every station in the table. Two-piece casting rod: he first suggests a butt of about 23 in and a 32-1/2 in tip to fit a 35 in rod case, then specifies a 6-1/2 oz rod with a 32-1/2 in butt (15/32 in at the grasp to 19/64 in at the ferrule) and a 33 in tip (17/64 in to 7/64 in), equal when ferrule and top are on. Make two tips for each rod.

Materiały do tego kroku:

Papier ściernyPapier ścierny1 sztuka

Potrzebne narzędzia:

Strug ręcznyStrug ręczny
Strug jednoręcznyStrug jednoręczny
Skrobak stalowySkrobak stalowy
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
SuwmiarkaSuwmiarka
5

Fit the ferrules

Fit a welted, shouldered ferrule at each joint, sized from his list: 17/64 in for the two-piece casting rod; 21/64 in and 15/64 in for the three-piece; 9/32 in and 11/64 in for the fly rods; 7/16 in for the salt-water rod; a 3/4 in male ferrule on the tarpon butt. The tip ferrule comes with two closed-end centres, one for each tip. Cement them on with ferrule cement; serrated (toothed) ferrule ends are wound with silk for strength.

Materiały do tego kroku:

Tulejka łącząca wędziskaTulejka łącząca wędziska2 sztuk
Klej do tulejekKlej do tulejek1 sztuka
Jedwab do owijekJedwab do owijek1 sztuka

Potrzebne narzędzia:

Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Palnik propanowyPalnik propanowy
SuwmiarkaSuwmiarka
6

Build the grasp and reel seat

Build the cork grasp and reel seat as for the one-piece rod: 3/4 in reel seat with straight hood for the casting rods (fly-rod type with butt cap on the fly rods, 9 in or 9-1/2 in of cork above it), 7/8 in on the salt-water rod with an 18 in double grasp, 1 in on the tarpon rod. Use a 1 in butt cap (1-1/8 in on the tarpon rod) and a taper (winding check) of the small-end size in his list. For an independent butt, fit the ferrule straight on a rounded dagame core so the seated ferrule does not touch the wood, cement and rivet it, fit a soft-pine sleeve over core and ferrule, glue it on, cement and rivet the reel seat, then glue on the corks and cut the core flush.

Materiały do tego kroku:

Pierścienie korkowePierścienie korkowe24 sztuk
Klej zwierzęcyKlej zwierzęcy1 sztuka
Deska sosnowaDeska sosnowa1 sztuka
Uchwyt kołowrotkaUchwyt kołowrotka1 sztuka
Kapsel dolnika wędziskaKapsel dolnika wędziska1 sztuka
Pierścień wykończeniowy rękojeściPierścień wykończeniowy rękojeści1 sztuka
Klej do tulejekKlej do tulejek1 sztuka
Nity miedzianeNity miedziane1 sztuka

Potrzebne narzędzia:

Nóż introligatorskiNóż introligatorski
Wiertarka ręcznaWiertarka ręczna
Strug jednoręcznyStrug jednoręczny
Palnik propanowyPalnik propanowy
MłotekMłotek
7

Mount the guides and tops

Casting rods: two 1/2 in narrow agate guides, two No. 1 one-ring casting guides and two 3/32 in offset agate tops. Fly rods: two No. 4 snake guides on the butt joint, three No. 3 on the middle joint, three No. 2 on each tip, and two No. 7 agate angle fly tops of the wind-on kind. Salt-water rod: a 10/32 in stirrup-tube agate top and two No. 3 bell guides. Tarpon rod: two No. 11 wide raised agate guides, two No. 1 trumpet guides and a 3/8 in agate stirrup top; whip its guides on double, the first set 10 in from the top, the second 26 in from the reel. Whip with 00 silk (00 or 0 on the three-piece rod, size A on the salt-water and tarpon rods), using the invisible knot.

Materiały do tego kroku:

Przelotka wędziskaPrzelotka wędziska8 sztuk
Przelotka szczytowaPrzelotka szczytowa2 sztuk
Jedwab do owijekJedwab do owijek1 sztuka
Wosk pszczeliWosk pszczeli1 sztuka

Potrzebne narzędzia:

Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Nóż introligatorskiNóż introligatorski
8

Shellac and varnish

Shellac the windings and varnish the rod with coach varnish as for the one-piece rod: thin coats, warm, three days between coats.

Materiały do tego kroku:

Politura szelakowaPolitura szelakowa1 sztuka
Lakier powozowyLakier powozowy3 sztuk

Potrzebne narzędzia:

Pędzel szerokiPędzel szeroki
9

Troubleshooting

Jointed rod troubleshooting.

Flow

Loading...
10

History and honest limits

From "Fishing-Rod Making and Angling, Part II" by Stillman Taylor, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 69-72). Two points are given as he wrote them: the two-piece casting rod's butt is about 23 in in one sentence and 32-1/2 in in the next; the three-piece rod's stock is "2 ft. long" while its finished sections are 21-1/2, 21-3/4 and 21 in. Guide counts in the list are for the fly rods, the largest set. The tools and metric figures are ours.

Materiały

17

Wymagane narzędzia

12

Według tego planu powstaje

Powiązane blueprinty

Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...