Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Leather Punch from an Old Pipe Nipple: Edge Ground Thin, Slug Slot Cut Above (Boy Mechanic, 1915)
A shop-made hollow punch for round holes in leather from The Boy Mechanic, Book 2 (1915): an old pipe nipple of the size you need, one end ground on the outside to a very thin cutting edge, and a small slot a little above it to push the leather slugs out.
Początkujący
Half an hour
Instrukcje
1
1
Read the tip
Read the tip
"The cutter end can be ground very thin to prevent an over-cut, while a small slot cut a little above it will allow the removal of the leather slugs."
2
2
Choose the pipe
Choose the pipe
Pick an old pipe nipple whose bore matches the hole you want: pieces of almost any size turn up around a shop. If the piece is long, saw it to a handy length (ours).
Materiały do tego kroku:
Rura stalowa (grubościenna, z gwintowanymi końcami)1 sztukaPotrzebne narzędzia:
Imadło warsztatowe
Piła do metalu3
3
Grind the cutter end
Grind the cutter end
Grind one end on the outside to a long bevel, leaving a very thin edge round the bore, as the hatched section in the sketch shows. Keep turning the pipe so the edge stays even.
Potrzebne narzędzia:
Szlifierka stołowa4
4
Cut the slug slot
Cut the slug slot
A little above the edge, cut a small slot through the wall (the sketch shows a triangle) to push the slugs out. Ours: drill a hole and file it to shape.
Potrzebne narzędzia:
Imadło warsztatowe
Wiertarka stołowa
Pilniki (pilnik ręczny)
Pilniki iglaki5
5
Punch
Punch
Ours: lay the leather on end-grain wood, stand the punch upright and strike the top with a mallet. Poke the slugs out through the slot.
Potrzebne narzędzia:
Pobijak drewniany6
6
Troubleshooting
Troubleshooting
Punch troubleshooting.
Flow
Loading...
7
7
History and honest limits
History and honest limits
From "Pipe Used as a Leather Punch", **The Boy Mechanic, Book 2** (Popular Mechanics, 1915), p. 138 (checked on the archive.org scan boymechanicbook200chic2). The note gives no sizes; the way the slot is cut, the length and the striking method are ours.
Materiały
1- Zastępnik
Wymagane narzędzia
7- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.


