Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Brazing Torch: a Pressure-Tank Gasoline or Kerosene Torch (Shop Notes, 1909)
Forge

Autor

Forge

4. listopad 2026NO
14
0
0
0
0

Brazing Torch: a Pressure-Tank Gasoline or Kerosene Torch (Shop Notes, 1909)

A shop brazing and tempering torch: a wall-hung pipe tank of gasoline or kerosene pumped up with a bicycle pump, feeding a 1/8 in pipe whose end is coiled round a short 1 in pipe; the flame heats the coil, the oil turns to gas, and it blasts out through a pinhole cap. Two burners on a tee give a bigger heat. Source: Popular Mechanics Shop Notes for 1909, pp. 861-862. Picture: the article's drawing.
Średniozaawansowany
Unknown

Instrukcje

1

Make the tank

Cap both ends of a 2 in pipe 20 in long. Drill three holes in the top cap: one for the rubber tube from a bicycle pump, one for a steam gauge, and one with a screw plug for filling with fuel oil.

Materiały do tego kroku:

Rura stalowa (grubościenna, z gwintowanymi końcami)Rura stalowa (grubościenna, z gwintowanymi końcami)1 2 in x 20 in
Złączka gwintowana do rurZłączka gwintowana do rur3 two caps, plug
ManometrManometr1 sztuka
Wąż gumowyWąż gumowy1 sztuka

Potrzebne narzędzia:

Wiertarka ręcznaWiertarka ręczna
Zestaw do gwintowaniaZestaw do gwintowania
Klucz hydraulicznyKlucz hydrauliczny
Pompka podłogowa do roweruPompka podłogowa do roweru
2

Coil the burner

Drill the bottom cap and connect a 1/8 in pipe D, any length, with a globe valve in it to set and shut off the oil. Fill the last 10 in of the pipe with lead, coil it round a 1 in pipe F 6 in long, and turn the end out to take two elbows and a short nipple; then melt the lead out. Drill a small hole in the centre of a 1/8 in cap and fit it on the end (E) so the hole lines up with the centre of pipe F.

Materiały do tego kroku:

Rura stalowa (grubościenna, z gwintowanymi końcami)Rura stalowa (grubościenna, z gwintowanymi końcami)1 1/8 in, and 1 in x 6 in
Złączka gwintowana do rurZłączka gwintowana do rur4 two elbows, nipple, 1/8 in cap
Zawór grzybkowyZawór grzybkowy1 sztuka

Potrzebne narzędzia:

OłówOłów
Cedzak dziurkowanyCedzak dziurkowany
Palenisko kowalskiePalenisko kowalskie
Wiertarka ręcznaWiertarka ręczna
Klucz hydraulicznyKlucz hydrauliczny
3

Start the burner

Hang a little cup holding three or four teaspoonfuls of oil just below the coil and light it to heat the coil; then pump up the tank and open the globe valve. For more heat connect two burners on a tee so their blasts meet.

Potrzebne narzędzia:

NaftaNafta
Pompka podłogowa do roweruPompka podłogowa do roweru

Materiały

5

Wymagane narzędzia

8

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...