Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Screw-Depth Portable Router: The Motor's Threaded Casing Screws Into a Split Base, One Turn per Sixteenth (Carter, 1924)
Forge

Autor

Forge

13. listopad 2026NO
8
0
0
0
0

Screw-Depth Portable Router: The Motor's Threaded Casing Screws Into a Split Base, One Turn per Sixteenth (Carter, 1924)

Ray L. Carter of Syracuse, New York, received US 1,514,894, dated 11 November 1924, for the portable electric router: a small high-speed motor in an insulated casing light enough to hold in one hand, with a cutter in a chuck on its shaft. The casing is threaded outside and screws into the split, threaded top of a hollow base with a flat bottom. Each turn moves the cutter 1/16 inch, and a clamp screw across the split locks it. The base is cut away so the cutter can be seen and the chips can get out. We print the casing and base in PETG at his pitch, round a small DC motor. The other sizes are ours.
Średniozaawansowany
About 2 days

Instrukcje

1

One turn, one sixteenth

Wczytywanie notatnika Jupyter…
2

Read US 1,514,894

"In practice, the threads of the shell 3 and support 9 are preferably about one-sixteenth inch pitch, so that each revolution of the motor or support in either direction moves the tool A correspondingly."
3

Print the motor casing

The casing 3: a tube for a 42 mm motor with a 60 mm thread at 1/16 inch pitch, an 18 mm hole and air slots in its bottom, and two holes 29 mm apart for the motor's face screws. Print it bottom down. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
Plik projektowySTLCC0 - Free
4

Print the base

The support 9: a hollow base with a flat plate 140 mm across and an opening 50 mm wide, its sides cut away, two wings, and the split, threaded top with clamp lugs. Print it plate down. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
Plik projektowySTLCC0 - Free
5

Print and fit the parts

Print the casing and the base in PETG. Clean the threads and screw the casing into the base by hand; it should turn smoothly all the way. If it is tight, run it in and out a few times. Check the base's bottom is flat by rubbing it on abrasive paper on a flat board.

Materiały do tego kroku:

Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
GradownikGradownik
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
6

Motor, collet and wiring

Fit the collet adapter on the motor's shaft and tighten its set screws. Push the motor down into the casing so its face sits on the casing's bottom with the collet through the hole, and screw it in with its two M4 face screws. Solder the supply leads through a toggle switch, sleeve the joints, and lead the cable out through the casing's open top. Set the DC supply to the motor's rated voltage.

Materiały do tego kroku:

Silnik elektrycznySilnik elektryczny1 sztuka
Adapter tulejki zaciskowej na wałek silnikaAdapter tulejki zaciskowej na wałek silnika1 sztuka
Śruba z łbem walcowym na imbusŚruba z łbem walcowym na imbus2 sztuk
Przełącznik dźwigniowyPrzełącznik dźwigniowy1 sztuka
Przewód montażowyPrzewód montażowy1 sztuka
Koszulka termokurczliwaKoszulka termokurczliwa1 sztuka

Potrzebne narzędzia:

Zasilacz prądu stałegoZasilacz prądu stałego
Lutownica elektrycznaLutownica elektryczna
Zestaw kluczy imbusowychZestaw kluczy imbusowych
Klucz nastawnyKlucz nastawny
7

Set the depth and lock it

Fit a straight bit in the collet. Screw the casing into the base until the bit's end is level with the base's bottom on a flat board, then screw it in four more turns for a 1/4 inch (6.35 mm) deep cut. Put an M5 screw through the lugs with a wing nut and tighten it, closing the split on the thread.

Materiały do tego kroku:

Śruba z łbem walcowym na imbusŚruba z łbem walcowym na imbus1 sztuka
Nakrętka skrzydełkowaNakrętka skrzydełkowa1 sztuka

Potrzebne narzędzia:

Zestaw frezów do frezarkiZestaw frezów do frezarki
Zestaw kluczy imbusowychZestaw kluczy imbusowych
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
8

Rout a groove

Clamp a board down. Hold the router by its casing and wings, base flat on the board, switch on, and move it along a clamped straightedge so the bit cuts a groove. Take deep grooves in two or three passes, a few turns deeper each time.

Potrzebne narzędzia:

Deska z drewna liściastegoDeska z drewna liściastego
Ścisk stolarski listwowyŚcisk stolarski listwowy
Okulary ochronneOkulary ochronne
9

Troubleshooting

Router troubleshooting.

Flow

Loading...
10

History and honest limits

**Ray L. Carter** of Syracuse, New York, US 1,514,894, dated 11 November 1924, filed 29 September 1923. He claimed a motor with a threaded casing, "a hollow cylinder having a split threaded portion adapted to engage the threaded portion of said casing whereby said tool may be moved relatively to the work", a plane bottom to move over the work, and means for locking. His motor ran on mains through a lamp socket at over 7,000 r.p.m.; ours is a small DC motor on a bench supply, a light-duty router. His casing was insulating material; ours is printed PETG. His fan and baffle disk are left out. The pitch is his; the other sizes are ours.

Materiały

8

Wymagane narzędzia

11

Pliki projektowe

2

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...