SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways
Martin

Autor

Martin

6. październik 2026NO
7
0
0
0
0

Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways

A single whisk carries the egg round with it rather than cutting through it. James F. Monroe of Fitchburg, Massachusetts, and E. P. Monroe of New York received US 23,694, dated 19 April 1859, for an egg beater: a frame clamped to a table carries a bevel wheel turned by a handle, gearing into two pinions on opposite sides of it; one turns an inner beater of bent wires, the other an outer beater round it, "in opposite directions." This rung works out the beater speeds, then prints the crown wheel and pinions, bends the beaters, and times a beating.
Średniozaawansowany
About 5 hours, plus printing

Instrukcje

1

Beater speeds

Wczytywanie notatnika Jupyter…
2

The gear train it uses

The embedded blueprint works gear ratios and direction. Monroe takes two pinions off opposite sides of one wheel so they turn opposite ways.
3

Read US 23,694

"This invention consists in arranging in an adjustable frame two beaters, one inside the other, which receive motion in opposite directions by means of two pinions which gear into a large bevel wheel and on opposite sides of the same, so that by rotating the bevel wheel by means of a handle the beaters receive the required motion."
4

Print the gears

Print the 48-tooth crown wheel (/uploads/blueprints/counter-rotating-egg-beater-crown-wheel.stl) and two 12-tooth pinions (/uploads/blueprints/counter-rotating-egg-beater-pinion.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.

Materiały do tego kroku:

Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
5

Build the frame

Cut a plywood upright and two arms. Bolt the crown wheel to the upright on an M5 screw with washers so it turns freely, and fix a handle screw near its rim. Drill the arms 5 mm on the line through both pinions' centres.

Materiały do tego kroku:

Płyta sklejkowaPłyta sklejkowa1 sztuka
Śruby maszynoweŚruby maszynowe1 sztuka
Podkładka płaskaPodkładka płaska1 sztuka
Nakrętka sześciokątnaNakrętka sześciokątna1 sztuka
Wkręt do drewna #8 x 1"Wkręt do drewna #8 x 1"1 sztuka

Potrzebne narzędzia:

Piłka włosowaPiłka włosowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Klucz nastawnyKlucz nastawny
Zestaw wkrętakówZestaw wkrętaków
6

Arbor and inner beater

Cut 200 mm of 5 mm rod. Epoxy one pinion on it to mesh at the wheel's top, and bend two wire loops 28 mm across at its lower end.

Materiały do tego kroku:

Pręt ze stali niskowęglowejPręt ze stali niskowęglowej1 sztuka
Drut ze stali nierdzewnejDrut ze stali nierdzewnej1 sztuka
Epoksyd dwuskładnikowyEpoksyd dwuskładnikowy1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Szczypce okrągłeSzczypce okrągłe
Szczypce płaskieSzczypce płaskie
7

Sleeve and outer beater

Glue the second pinion to a length of silicone tube sleeved loosely over the rod, meshing at the wheel's bottom. Bend two wire loops 48 mm across and fix them to the sleeve's lower end, round the inner beater.

Materiały do tego kroku:

Wężyk silikonowyWężyk silikonowy1 sztuka
Drut ze stali nierdzewnejDrut ze stali nierdzewnej1 sztuka
Epoksyd dwuskładnikowyEpoksyd dwuskładnikowy1 sztuka

Potrzebne narzędzia:

Szczypce okrągłeSzczypce okrągłe
Szczypce płaskieSzczypce płaskie
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
8

The patent drawing

US 23,694 drawing sheet, public domain (expired patent).
Krok 8 - Image 1
9

Beat egg whites

Clamp the frame to the table over the bowl with two egg whites. Turn the handle about once a second and time how long until they hold stiff peaks.
Krok 9 - Image 1

Materiały do tego kroku:

JajoJajo2 sztuk

Potrzebne narzędzia:

Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
StoperStoper
10

Beaters that turn together, jam or clash

Counter-rotating egg beater troubleshooting.

Flow

Loading...
11

History and honest limits

**James F. Monroe** of Fitchburg, Massachusetts, and **E. P. Monroe** of New York, assignors to E. P. Monroe, received US 23,694, dated 19 April 1859, reissued 16 October 1860 (No. 1,062). The frame's fork clamps to a table with a set screw and washer. The second pinion lies loose on the arbor, driving the outer beater whose lower collar turns loosely round the arbor's end. They noted it also mixes paint. **Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. A crown wheel and spur pinions stand in for his bevel gears, and a silicone sleeve for his loose pinion. Your times are the result.

Materiały

11

Wymagane narzędzia

12

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...