Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Electric Arc Furnace: the Héroult Series-Arc Steel Furnace (Stansfield, 1914)
Volt

Autor

Volt

4. listopad 2026SE
18
0
0
0
0

Electric Arc Furnace: the Héroult Series-Arc Steel Furnace (Stansfield, 1914)

Héroult's steel furnace: a tilting hearth like an open-hearth furnace, lined with dolomite, with two carbon electrodes coming down through the roof. The current goes down one electrode, arcs into the slag, passes through the molten steel and arcs back up the other, so the heat goes straight into the metal. Result: an electric steel furnace about 7 x 4 ft inside for a 3 ton charge, run at about 350 kW and 110 V. Source: A. Stansfield, The Electric Furnace, 2nd ed. (1914), pp. 115-116, 214-216. Unknown: case and tilting gear details, electrode size. Picture: a drawn diagram (Fig. 93 is blank in the scan).
Ekspert
Unknown

Instrukcje

1

Build the case and lining

Build the furnace in a steel case on a tilting mounting, about 7 x 4 ft inside, with charging doors at the ends. Line it with dolomite bricks and crushed dolomite; dolomite or magnesite on the hearth, which allows strongly basic slags. Ours: mild steel plate. Not given: the case and tilting gear, the bricks' making.

Materiały do tego kroku:

Blacha gruba ze stali niskowęglowejBlacha gruba ze stali niskowęglowej1 case
Dolomit (wapień magnezowy)Dolomit (wapień magnezowy)1 lining and crushed dolomite
Bloki magnezytoweBloki magnezytowe1 hearth, if magnesite

Potrzebne narzędzia:

Spawarka łukowaSpawarka łukowa
KielniaKielnia
Nieznane wymiaryNieznane wymiary
2

Make the removable roof

Make the roof of silica brick, covered with steel plates and given eyes so it can be lifted off. Between the two electrode holes use bronze plates instead of steel, because steel there would raise the inductance of the AC circuit. Fit water jackets round each electrode hole for a close fit, so less heat escapes and the electrodes do not burn in the air. Ours: copper tube for the water jackets. Silica brick has no head here.

Materiały do tego kroku:

Nieznany materiałNieznany materiał1 silica brick
Blacha gruba ze stali niskowęglowejBlacha gruba ze stali niskowęglowej1 roof plates
Blacha z brązuBlacha z brązu1 plates between electrodes
Rura miedzianaRura miedziana1 water jackets

Potrzebne narzędzia:

Spawarka łukowaSpawarka łukowa
Wiertarka stołowaWiertarka stołowa
WodaWoda
3

Hang the electrodes

Use two vertical carbon electrodes, square in section. Carry each in a holder on an arm supported by the furnace itself, so its height does not change when the furnace tilts: four contact pieces round the electrode, drawn tight by a steel strap and a screw in the arm, with the cable bolted to them. Raise and lower each electrode separately, by a regulator controlled by the voltage between it and the metal. Not given: electrode size, the regulator's build.

Materiały do tego kroku:

Elektroda węglowaElektroda węglowa2 electrodes
Nieznany metalNieznany metal1 holders, arms, contact pieces

Potrzebne narzędzia:

Wiertarka stołowaWiertarka stołowa
4

Melt and refine a charge

Charge steel scrap with some iron ore and lime. Keep each electrode a little above the slag, leaving room for its arc. Regulate the current by hand while the scrap melts, then switch to automatic; full power only after about an hour. Pour off the slag and make a second, then a third, with lime and a little sand and fluorspar, before the final additions. At La Praz this took about 350 kW at 110 V: 5 hours for 1.25 tons of low-carbon steel, 8 hours for 2.33 tons of high-carbon steel. Not given: the electric supply.

Potrzebne narzędzia:

WodaWoda

Materiały

8

Wymagane narzędzia

5

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...