SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

Autor

Penny

14. październik 2026DK
24
0
0
0
0

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
Średniozaawansowany
Two to three days

Instrukcje

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

Materiały do tego kroku:

Płaskownik ze stali narzędziowejPłaskownik ze stali narzędziowej1 sztuka

Potrzebne narzędzia:

Pilnik do metaluPilnik do metalu
Wiertarka ręcznaWiertarka ręczna
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
Kuźnia kowalskaKuźnia kowalska
Kadź hartowniczaKadź hartownicza
Okulary ochronneOkulary ochronne
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

Materiały do tego kroku:

Listwa z drewna twardegoListwa z drewna twardego2 sztuk
Pręt ze stali niskowęglowejPręt ze stali niskowęglowej0.3 m

Potrzebne narzędzia:

Pilnik do metaluPilnik do metalu
Kuźnia kowalskaKuźnia kowalska
Kadź hartowniczaKadź hartownicza
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

Materiały do tego kroku:

Blacha mosiężnaBlacha mosiężna1 sztuka
Woskowana nić lnianaWoskowana nić lniana3 m

Potrzebne narzędzia:

Nożyce do blachyNożyce do blachy
Wiertarka ręcznaWiertarka ręczna
Pilnik do metaluPilnik do metalu
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

Potrzebne narzędzia:

Pilnik do metaluPilnik do metalu
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

Materiały do tego kroku:

Sztaba mosiądzuSztaba mosiądzu2 kg
Węgiel drzewnyWęgiel drzewny1 as required
Piasek formierskiPiasek formierski5 kg

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Tygiel z gliny ogniotrwałejTygiel z gliny ogniotrwałej
Szczypce do tyglaSzczypce do tygla
Skrzynka formierska (górna i dolna)Skrzynka formierska (górna i dolna)
Rękawice spawalniczeRękawice spawalnicze
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

Materiały do tego kroku:

WodaWoda1 litr

Potrzebne narzędzia:

Cylinder miarowyCylinder miarowy
Pilnik do metaluPilnik do metalu
7

A binary set of weights

Wczytywanie notatnika Jupyter…
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

Materiały

9

Wymagane narzędzia

12

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...