SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Forged Hunting Axe (Hatchet)
Forge

Autor

Forge

11. październik 2026NO
32
0
0
0
0

Forged Hunting Axe (Hatchet)

A small one-handed axe forged from a 7/8 × 2-inch bar of good tool steel, best made by two people; a 6¾-inch bar gives two heads. The eye, about 9/16 × 1½ inches, is punched at a yellow heat with an eye punch and opened with drifts, the blade drawn out to a 3-inch edge and the head cut to length. The axe is annealed in lime or ashes, ground and buffed, then hardened from the hardening heat in tepid water and tempered by two hot iron bars laid on either side at the centre: dark purple for the blade, blue for the head.
Zaawansowany
4–6 hours

Instrukcje

1

Mark and punch the eye

Mark the stock with chisel and centre punch. At a yellow heat, punch the eye with the narrow edge of the punch toward the blade; lift the punch after each blow to check it runs straight and to let it cool; a little fine coal in the hole stops it sticking. Punch nearly through, then finish from the other side.

Materiały do tego kroku:

Płaskownik ze stali narzędziowejPłaskownik ze stali narzędziowej1 sztuka

Potrzebne narzędzia:

PunktakPunktak
Kuźnia kowalskaKuźnia kowalska
KowadłoKowadło
Przebijak na gorącoPrzebijak na gorąco
Młot dwuręcznyMłot dwuręczny
Szczypce kowalskieSzczypce kowalskie
2

Drift and draw out

Drive in a tool-steel drift, hammer the bulges down to the bar's size and smooth with a flatter; take the drift out before each reheat. Use two drifts, the first 3/8 inch narrower. Draw out the blade, driving the drift back in as the eye stretches so no cold shut forms.

Potrzebne narzędzia:

Przebijak rozszerzającyPrzebijak rozszerzający
Gładzik kowalskiGładzik kowalski
Młot ogoniastyMłot ogoniasty
3

Shape and trim

Shape the blade with a heavy hammer and flatter and form its edge. Cut the head from the bar, draw it to size, cut it to length, then trim the blade to shape.

Potrzebne narzędzia:

Młot kowalskiMłot kowalski
Gładzik kowalskiGładzik kowalski
Przecinak na gorącoPrzecinak na gorąco
4

Anneal and grind

Heat to a full red and anneal in lime or ashes. When cold, grind on an emery wheel and finish on a buffing wheel.

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Szlifierka stołowaSzlifierka stołowa
5

Harden and temper

Heat very slowly to the hardening heat and cool in tepid water. Draw the temper with two hot iron bars laid on either side at the centre; when the blade is dark purple and the head blue, cool quickly in water.

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Kadź hartowniczaKadź hartownicza
Szczypce kowalskieSzczypce kowalskie
6

Handle

Shave the handle stock to fit the eye tightly, drive the head on, saw a kerf in the handle's top and drive a glued hardwood wedge into it. Trim flush and oil the handle.

Materiały do tego kroku:

Listwa z drewna twardego na trzonkiListwa z drewna twardego na trzonki1 sztuka
Klin z drewna twardegoKlin z drewna twardego1 sztuka
Olej lnianyOlej lniany10 ml

Potrzebne narzędzia:

Strug kabłąkowyStrug kabłąkowy
Piła traczkaPiła traczka
Imadło warsztatoweImadło warsztatowe

Materiały

4

Wymagane narzędzia

16

Według tego planu powstaje

Powiązane blueprinty

Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...