Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Fused Quartz Tube: Blown from Brazil Pebble in the Oxy-Gas Flame (Shenstone, 1916)
Charlie

Autor

Charlie

4. listopad 2026DE
16
0
0
0
0

Fused Quartz Tube: Blown from Brazil Pebble in the Oxy-Gas Flame (Shenstone, 1916)

Fused silica stands sudden heating and cooling that would crack glass, but natural quartz splinters violently in a flame. W. A. Shenstone, in The Methods of Glass-Blowing and of Working Silica in the Oxy-Gas Flame (1916), first turns Brazil pebble into a "non-splintering" silica by quenching it from a yellow-red heat, then melts it in an oxy-gas flame into fine rods, wraps the rods round a platinum core into a first tube, and enlarges it with rings of rod blown out. Not given: quantities and times. He advises most workers to start from bought tubes and to learn each stage by practice. Source: W. A. Shenstone (1916), pp. 88-94. Picture: his p. 93.
Zaawansowany
Several days of practice

Instrukcje

1

Read Shenstone

"The silica tubes thus made can be cut and broken like glass, they can be joined together before the flame, and they can also be drawn into smaller tubes when softened by heat."
2

Crack the Brazil pebble

Clean the chips of Brazil pebble (rock crystal) thoroughly, heat them in boiling water and drop them into cold water. Repeat until they have cracked enough to break easily with a clean steel pestle or hammer. Hand-pick the fragments and reject any that are not perfectly free from foreign matter.

Materiały do tego kroku:

Kryształ górskiKryształ górski1 as required
WodaWoda1 as required

Potrzebne narzędzia:

Rondel o wysokich ściankachRondel o wysokich ściankach
Płyta grzejnaPłyta grzejna
WiadroWiadro
Młotek ślusarski z kulistym rąbemMłotek ślusarski z kulistym rąbem
3

Make it non-splintering

Heat the pure, transparent pieces to a yellow-red heat in a covered platinum dish in a muffle furnace and plunge them quickly into a deep clean vessel of distilled water. Repeat until they are semi-opaque, friable masses like white enamel. Wash them with distilled water, drain and dry. Now they can go straight into the hottest part of the flame without splintering.

Materiały do tego kroku:

Woda destylowanaWoda destylowana1 as required

Potrzebne narzędzia:

Parownica platynowaParownica platynowa
Piec muflowyPiec muflowy
Szczypce do tyglaSzczypce do tygla
Zlewka szklanaZlewka szklana
4

Set up the flame

Use an efficient oxy-gas burner fed with coal gas and oxygen from a bottle fitted with a gauge and regulator; watch the oxygen used. Protect your eyes with very dark glasses, so dark that work is a little difficult at first, and keep a second pair for long spells, as the glasses get hot. The hottest spot is near the tip of the inner cone: bring the work exactly there.

Materiały do tego kroku:

Gaz świetlnyGaz świetlny1 as required
TlenTlen1 as required

Potrzebne narzędzia:

Palnik tlenowo-gazowyPalnik tlenowo-gazowy
Butla na gaz pod ciśnieniemButla na gaz pod ciśnieniem
Reduktor ciśnieniaReduktor ciśnienia
ManometrManometr
Przyciemniane gogle kowalskiePrzyciemniane gogle kowalskie
5

Draw fine rods

Hold a fragment in platinum-tipped forceps and melt one corner. Press a second fragment against the melted part until they stick, and heat from below upwards (to avoid bubbles) until it is clear. Add a third, a fourth and so on until you have an irregular rod. Reheat it in sections and draw it out into rods or coarse threads 1 to 2 mm across.

Potrzebne narzędzia:

Szczypce z końcówkami platynowymiSzczypce z końcówkami platynowymi
Palnik tlenowo-gazowyPalnik tlenowo-gazowy
Przyciemniane gogle kowalskiePrzyciemniane gogle kowalskie
6

Make the first tube

Bind a few rods round a platinum rod about 1 mm across with platinum wires at both ends. Withdraw the core slightly from one end and heat gradually from there until a rough tube 4 to 5 cm long has formed. Close one end, blow it into a small bulb, fix a silica rod to the far end of the bulb, reheat and draw it out into a fine tube. Blow a fresh bulb on one end and draw it out again, until the tube is 6 to 8 cm long.

Potrzebne narzędzia:

Drut platynowyDrut platynowy
Szczypce z końcówkami platynowymiSzczypce z końcówkami platynowymi
Palnik tlenowo-gazowyPalnik tlenowo-gazowy
Przyciemniane gogle kowalskiePrzyciemniane gogle kowalskie
7

Blow without soiling it

Blow through a rubber tube on the open end of the silica tube, with a glass tube loosely packed with granulated potash between your mouth and the work so the inside stays clean. Do not take a hot bulb out of the flame to blow it; move it just off the hot spot. Mend holes with plastic silica from the softened end of a fine rod and blow the lump out. Keep the silica clean: a white crust that forms is removed by reheating, but dust or handling can spoil the surface for good.

Potrzebne narzędzia:

Wąż gumowyWąż gumowy
Rurka szklanaRurka szklana
Węglan potasu (potaż)Węglan potasu (potaż)
Palnik tlenowo-gazowyPalnik tlenowo-gazowy
8

Enlarge and lengthen

To widen a bulb into a tube, lay a ring of fine rod round its end, heat the ring and the end until soft and blow; repeat until the bulb becomes a short tube. For a long tube make several pieces 200 to 250 mm long at the diameter you need and join them end to end. Thicken a tube by adding rings and blowing them out. For a large tube, set a plate of silica behind the work to throw the flame back onto its far side.

Potrzebne narzędzia:

Palnik tlenowo-gazowyPalnik tlenowo-gazowy
Szczypce z końcówkami platynowymiSzczypce z końcówkami platynowymi
Przyciemniane gogle kowalskiePrzyciemniane gogle kowalskie
9

History and honest limits

Thorpe's Dictionary (vol. IV, 1913) records Gaudin spinning fused silica threads in 1839, Boys making quartz fibres in 1887, and Shenstone showing in 1901 how to make tubes and bulbs before the oxy-coal-gas blowpipe. Shenstone gives no quantities or times and says most workers save time and money by starting from bought silica tubes. A finished tube holds a little moisture and nitric peroxide; he removes them by heating it and drawing filtered air through, not by washing.

Materiały

5
  • 1 as required
    Zastępnik
  • 1 as required
    Zastępnik
  • 1 as required
    Zastępnik
  • 1 as required
    Zastępnik
  • 1 as required
    Zastępnik

Wymagane narzędzia

18

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...