Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Gasholder: Water-Sealed Zinc Gasometer with Balance Weights (Ramsay & Travers, 1898)
The laboratory gasometer Ramsay and Travers used to store argon: a zinc bell that rises and falls in a narrow ring of water between two fixed zinc cylinders. Because the water space is only about 2 cm wide, little gas dissolves in it. Weights on cords over pulleys balance the bell, and weights laid on top push the gas out.
Result: a water-sealed gasholder of 18 to 180 litres.
Source: M. W. Travers, The Experimental Study of Gases (1901), pp. 30 and 105-106. Unknown: sizes and how the zinc is joined. Picture: Fig. 34, the small mercury form of the same design.
Średniozaawansowany
Unknown
Instrukcje
1
1
Make the fixed cylinders
Make the fixed cylinders
Make two concentric zinc cylinders on a closed base, leaving a ring-shaped space about 2 cm wide between them for the water. Make the top of the inner cylinder dome-shaped. Bring a gas pipe with a stopcock up through the inner cylinder. Ours: zinc soldered with tin-lead solder. Not given: sizes, how the zinc is joined, the stopcock.
Materiały do tego kroku:
Blacha cynkowa1 outer and inner cylinders, base
Lut cynowo-ołowiowy1 seams
Nieznany zawór1 gas stopcockPotrzebne narzędzia:
Nożyce do blachy
Lutownica
Nieznana metoda kształtowania
Nieznane wymiary2
2
Make and hang the bell
Make and hang the bell
Make the gasholder bell of zinc to fit closely over the inner cylinder and down into the water ring, with a dome-shaped top matching the inner cylinder's, so all the gas can be pushed out. Ramsay and Travers made bells of about 180, 27, 18 and 18 litres. Tie a cord to the top of the bell and pass it over pulleys to a hanging weight, to take the bell's own weight off the gas. Fill the ring with water. To deliver gas, take weight off the cord or lay weights on top of the bell. Not given: the weights.
Materiały do tego kroku:
Blacha cynkowa1 bell
Lut cynowo-ołowiowy1 seams
Sznurek konopny1 balance cords
Krążek2 pulleys
Nieznany metal1 balance weightsPotrzebne narzędzia:
Nożyce do blachy
LutownicaMateriały
6- 1 bellZastępnik
- 2 seamsZastępnik
- 1 gas stopcockZastępnik
- 1 balance cordsZastępnik
- 2 pulleysZastępnik
- 1 balance weightsZastępnik
Materiały z połączonych planów

10% atrybucji
Zinc Sheet Cast as a Plate and Hammered Warm
autor: Forge
Obróbka metali
23
0
0
0
1
0

Niebezpieczne
10% atrybucji
Making Tin-Lead Solder — The Ancient Alloy That Joins Metals Without a Forge
autor: Peter
Obróbka metali
62
0
0
0
3
0

10% atrybucji
Hand-Spun Three-Ply Hemp Cord
autor: Tex
Tekstylia i skóra
43
0
0
0
1
0
Według tego planu powstaje
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.
