Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Half-Round Taper Reamer: Tool Steel Turned to the Taper, Filed Flat to the Centre Line, Hardened (Griswold, Amateur Work, 1905)
Forge

Autor

Forge

14. listopad 2026NO
9
0
0
0
0

Half-Round Taper Reamer: Tool Steel Turned to the Taper, Filed Flat to the Centre Line, Hardened (Griswold, Amateur Work, 1905)

The simplest home-made taper reamer, from Robert Gibson Griswold's Tool Making for Amateurs (Boston, 1905): tool steel turned to the taper wanted (his was 1/8 in. per foot), one side filed away exactly to the centre line so that two cutting edges remain, then hardened and ground on the flat face only. It reams a very smooth conical hole.
Średniozaawansowany
Two to three hours

Instrukcje

1

His taper

Wczytywanie notatnika Jupyter…
2

Read Griswold

"Turn a piece of tool steel to the proper taper and then file away one side until the flat surface coincides with the center line."
3

Turn the taper

Turn a piece of tool steel in the lathe to the taper of the part the hole must fit (his: 1/8 in. per foot). Length and diameter are ours: a little longer than the hole and spanning its two diameters.

Materiały do tego kroku:

Pręt ze stali narzędziowejPręt ze stali narzędziowej1 sztuka

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
SuwmiarkaSuwmiarka
4

File to the centre line

Hold it in the vice and file away one side until the flat face lies exactly on the centre line. This leaves a cutting edge on each side.

Potrzebne narzędzia:

Imadło warsztatoweImadło warsztatowe
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
SuwmiarkaSuwmiarka
5

Harden and grind

Harden it (ours: heat to a cherry red and quench in water, temper to a straw colour), then grind on the flat side only, never on the round.

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Kadź hartowniczaKadź hartownicza
Szlifierka stołowaSzlifierka stołowa
6

Troubleshooting

Reamer troubleshooting.

Flow

Loading...
7

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" VII, **Amateur Work** (Boston), vol. IV (1904-05), p. 128 (checked on the archive.org scan amateurwork04bostrich). He gives no size or temper for the reamer; those and the tools are ours. He finishes the hardened bushings with a copper lap and emery.

Materiały

1

Wymagane narzędzia

7

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...