Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Hackle Combs: Coarse and Fine Flax Heckles on One Board (Ure, 1839)
Woody

Autor

Woody

4. listopad 2026NO
12
0
0
0
0

Hackle Combs: Coarse and Fine Flax Heckles on One Board (Ure, 1839)

A pair of flax heckles on one oblong plank: two round wooden blocks, each faced with a drilled brass or iron plate holding upright iron teeth. Flax is drawn first through the coarse heckle, then through the fine one, splitting the fibres, combing out the short tow and laying the long fibres straight. Coarse: teeth about 1/10 in thick and 1 1/4 in long, a centre tooth and 12 rings, the outer ring 5 3/4 in across. Fine: thinner teeth set closer, 1109 of them. Source: Andrew Ure, Dictionary of Arts, Manufactures and Mines (1839), 'Flax'. Picture: Figs. 424-425 of the book.
Średniozaawansowany
Unknown

Instrukcje

1

Make the board and blocks

Cut an oblong plank (Fig. 424, a b) and two round (or square) wooden blocks, c for the coarse heckle and d for the fine, and fix the blocks on the plank (Fig. 425). The heckles can also be made on separate boards.

Materiały do tego kroku:

Deska z drewna twardegoDeska z drewna twardego1 sztuka
Klocek z drewna twardegoKlocek z drewna twardego2 sztuk
Wkręty do drewnaWkręty do drewna1 sztuka

Potrzebne narzędzia:

Piła grzbietnicaPiła grzbietnica
Wkrętak płaskiWkrętak płaski
2

Drill the face plates

Cover the top of each block with a brass or iron plate drilled for the teeth, which gives them a firmer hold. Set the holes evenly over the whole face, in concentric circles (the German way) or parallel rows (the English way). Coarse: a centre hole and 12 rings, the outermost 5 3/4 in across. Fine: thinner holes set closer, 1109 in all.

Materiały do tego kroku:

Blacha mosiężnaBlacha mosiężna2 face plates

Potrzebne narzędzia:

Cyrkiel traserskiCyrkiel traserski
Nożyce do blachyNożyce do blachy
Wiertarka ręcznaWiertarka ręczna
3

Make the teeth

Cut teeth of iron (sometimes steel) 1 to 2 in long. For the coarse heckle make them about 1/10 in thick and 1 1/4 in long, tapering from the middle to a very fine point; the fine heckle's teeth are thinner. File every point sharp and smooth, running evenly into the round stem like a sewing needle; square points in a rhombus shape cut the fibres apart better than round ones.

Materiały do tego kroku:

Drut żelaznyDrut żelazny1 teeth

Potrzebne narzędzia:

Nożyce do blachyNożyce do blachy
Pilnik do metaluPilnik do metalu
4

Set the teeth

Drive each tooth through its hole in the plate into the block so it stands upright, all points at one level.

Potrzebne narzędzia:

MłotekMłotek

Materiały

5

Wymagane narzędzia

7

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...