Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Cart Crupper, Breeching, Belly-Band and Straps (Hasluck, Harness Making, 1904)
Tex

Autor

Tex

13. listopad 2026FO
6
0
0
0
0

Cart Crupper, Breeching, Belly-Band and Straps (Hasluck, Harness Making, 1904)

The rest of a cart harness, from Paul N. Hasluck's Harness Making (1904): the crupper that runs from the saddle under the tail, the breeching round the hindquarters with its tugs and loin straps, the belly-band, hame straps and a leading rein. All sizes are his. With the bridle, collar and cart saddle it completes the set.
Zaawansowany
About 3 days

Instrukcje

1

Cutting list

Wczytywanie notatnika Jupyter…
2

Read Harness Making, ch. VII

"To make the breeching, cut the body, if possible, 7 ft. 4 in. long and about 4 in. wide. Turn it down to 4 ft. 10 in. long, the strong end less than the weak."
3

Cut the crupper body and dock

Cut the body 2 ft 6 in or 2 ft 8 in long and 3½ to 4 in wide; cut a semicircle in the centre from the weak end, leaving a point about ¾ in wide each side, and cut an 8 in piece to line this end. Cut a piece ⅞ in wide and 8½ in long, shave its ends, and stitch it edge to edge into a round to within 1½ in of each end, with a cord or strip of leather inside; rub it round, blacken it and flatten both ends with a hammer.

Materiały do tego kroku:

Skóra uprzężowaSkóra uprzężowa1 sztuka
Sznurek konopnySznurek konopny1 sztuka
Nić skórzanaNić skórzana1 sztuka
Barwnik do skóryBarwnik do skóry1 sztuka

Potrzebne narzędzia:

Nóż do skóryNóż do skóry
Dwie igły rymarskieDwie igły rymarskie
SzydłoSzydło
Młotek ciesielskiMłotek ciesielski
4

Finish the crupper body

Point the square end, reducing it to about 2 in. Race it along the sides and ends, edge and black it, and run a hot iron over the creases. Prick it about nine per inch as far as the lining reaches from the semicircle. Put the ends of the round piece under the points, one each side, the lining under them, and stitch all round and across the points with three-cord black-wax thread; trim, black and rub the edges.

Materiały do tego kroku:

Nić skórzanaNić skórzana1 sztuka
Barwnik do skóryBarwnik do skóry1 sztuka

Potrzebne narzędzia:

Nóż do skóryNóż do skóry
Cyrkiel rymarski do rowkowaniaCyrkiel rymarski do rowkowania
Fazownik krawędziFazownik krawędzi
Ukośnik rymarskiUkośnik rymarski
Palnik propanowyPalnik propanowy
Przecinak do szycia skóryPrzecinak do szycia skóry
SzydłoSzydło
Dwie igły rymarskieDwie igły rymarskie
Kozioł rymarskiKozioł rymarski
5

Make the crupper lay

Cut the lay 1 in narrower than the body and 3 ft long; turn in 10 in at the strong end and beat it flat. Turn the other end down 2 in and cut it slanting to 1½ in for a buckle, with a buckle hole. Mark cross lines 2 in from the broad point, ¼ in from the end of the bend underneath, and 2½ in from that toward the buckle. Edge the top only, crease two lines and hot-iron them, with inner lines about ¼ in in. Leave two openings for the hip straps, one in the bend and one in the middle; black and prick the stitched parts. Fix the buckle, lay it on the centre of the body with the broad end reaching the edge of the semicircle, tack and stitch, spotting the three cross lines.

Materiały do tego kroku:

Skóra uprzężowaSkóra uprzężowa1 sztuka
Żelazna klamra z kolcemŻelazna klamra z kolcem1 sztuka
Nić skórzanaNić skórzana1 sztuka
Barwnik do skóryBarwnik do skóry1 sztuka

Potrzebne narzędzia:

Nóż do skóryNóż do skóry
Fazownik krawędziFazownik krawędzi
BigownicaBigownica
Ukośnik rymarskiUkośnik rymarski
Dziurkacz do skóryDziurkacz do skóry
Przecinak do szycia skóryPrzecinak do szycia skóry
SzydłoSzydło
Dwie igły rymarskieDwie igły rymarskie
6

Pad the crupper and fit its strap

Cut thick felt as wide as the body, from the point of the semicircle to 2 in beyond the cross line near the buckle; cover it with basil, coarse-stitch it along the centre, turn the ends over and fasten them, and stitch it in place next the body with four or five stitches here and there, well secured at each corner. Cut a hole through the body opposite the buckle, 1½ in wide. Make a strap 9 in long, pointed one end and shaved the other, crease, black and stitch its shaved end to the narrow end of the body; it goes round the saddle's dock and up through the hole to the buckle on the lay.

Materiały do tego kroku:

Filc wełnianyFilc wełniany1 sztuka
Skóra owcza (basil)Skóra owcza (basil)1 sztuka
Skóra uprzężowaSkóra uprzężowa1 sztuka
Nić skórzanaNić skórzana1 sztuka
Barwnik do skóryBarwnik do skóry1 sztuka

Potrzebne narzędzia:

Nóż do skóryNóż do skóry
Dziurkacz do skóryDziurkacz do skóry
SzydłoSzydło
Dwie igły rymarskieDwie igły rymarskie
7

Make the breeching body

Cut the body 7 ft 4 in x about 4 in and turn it down to 4 ft 10 in, the strong end less than the weak; edge, black and crease two rows along the edges. Mark a cross line about 1½ in from the centre of the bend each side, and at each end. Line the bend with 1 ft pieces bent flesh outward, one end about 1 in shorter; prick, tack and stitch row to row to make the eye for the bridgeband pin. Trim, blacken and rub the bend with tallow and bone; beat it with a wooden mallet if hard, and stitch the double part along ends and sides.

Materiały do tego kroku:

Skóra uprzężowaSkóra uprzężowa1 sztuka
Nić skórzanaNić skórzana1 sztuka
Barwnik do skóryBarwnik do skóry1 sztuka
ŁójŁój1 sztuka

Potrzebne narzędzia:

Nóż do skóryNóż do skóry
Fazownik krawędziFazownik krawędzi
BigownicaBigownica
Przecinak do szycia skóryPrzecinak do szycia skóry
SzydłoSzydło
Dwie igły rymarskieDwie igły rymarskie
Kostka introligatorskaKostka introligatorska
Pobijak drewnianyPobijak drewniany
8

Put on the breeching lay

Cut the lay the same length and 1 in narrower; edge, crease and black it, run another line ¼ in inside the crease, prick the two inner lines nine to the inch and turn it down at both ends as the body. Tack it on the centre of the body, light end against heavy end, and stitch end to end to the cross lines, bulging the cross stitching inward about 1 in at the middle. Punch a large hole where the stitches bulge and cut straight out each side for the chain to catch the pin. Cut a slot for the 1½ in tug 1 ft 4 in from each end.

Materiały do tego kroku:

Skóra uprzężowaSkóra uprzężowa1 sztuka
Nić skórzanaNić skórzana1 sztuka
Barwnik do skóryBarwnik do skóry1 sztuka

Potrzebne narzędzia:

Nóż do skóryNóż do skóry
Fazownik krawędziFazownik krawędzi
BigownicaBigownica
Przecinak do szycia skóryPrzecinak do szycia skóry
Dziurkacz do skóryDziurkacz do skóry
SzydłoSzydło
Dwie igły rymarskieDwie igły rymarskie
9

Make the tugs and safes

Two hind tugs 1 ft 8 in long, 6 in turned down each end to meet; buckle hole in the weak end; black, crease, rub and prick them. Put the strong end up through the slot from underneath, joint in front under the loop, buckle on the other end; make a loop about 2½ in long round both thicknesses and pull it over the joint. Cut a safe for each from the breeching to an inch beyond the buckle and ½ in wider each side, narrowed and shaved at the bottom, rounded at the top with a loop; finish it on the 1½ in loop-stick, beat it flat and square, nail it from underneath with about five nails each side clinched on the loop-stick, and crease it again with a hot iron. Stitch the safes along the tugs. Make the front tugs for the bridgeband pins the same but shorter, so their length from the breeching equals the hind tugs; fit the pins with their nut and washer.

Materiały do tego kroku:

Skóra uprzężowaSkóra uprzężowa1 sztuka
Żelazna klamra z kolcemŻelazna klamra z kolcem4 sztuk
Sworzeń podpinkiSworzeń podpinki2 sztuk
GwoździeGwoździe1 sztuka
Nić skórzanaNić skórzana1 sztuka
Barwnik do skóryBarwnik do skóry1 sztuka

Potrzebne narzędzia:

Nóż do skóryNóż do skóry
Dziurkacz do skóryDziurkacz do skóry
Wzornik do szlufekWzornik do szlufek
Młotek ciesielskiMłotek ciesielski
Ukośnik rymarskiUkośnik rymarski
Palnik propanowyPalnik propanowy
BigownicaBigownica
Przecinak do szycia skóryPrzecinak do szycia skóry
SzydłoSzydło
Dwie igły rymarskieDwie igły rymarskie
Klucz nastawnyKlucz nastawny
10

Make the loin straps

Cut two loin straps 3 ft 8 in x 1½ in to fasten to the tugs and pass through the openings in the crupper; point each end, crease double each side, edge, black, hot-iron the creases and make six or seven holes in each end.

Materiały do tego kroku:

Skóra uprzężowaSkóra uprzężowa1 sztuka
Barwnik do skóryBarwnik do skóry1 sztuka

Potrzebne narzędzia:

Nóż do skóryNóż do skóry
Fazownik krawędziFazownik krawędzi
BigownicaBigownica
Ukośnik rymarskiUkośnik rymarski
Palnik propanowyPalnik propanowy
Dziurkacz do skóryDziurkacz do skóry
11

Make the leading rein and hame straps

Leading rein: a 1 in strap about 8 ft 6 in long in all, with a buckle and a billet 1 ft long at one end and a chain with a spring hook at the other; black and crease it and stitch on buckle, billet and chain. The chain goes through the near bit ring and hooks to the other ring; the billet fastens to the crupper. Hame straps: 1¼ in, about 1 ft 8 in long, buckle and loop at one end, the other pointed with holes.

Materiały do tego kroku:

Skóra uprzężowaSkóra uprzężowa1 sztuka
Żelazna klamra z kolcemŻelazna klamra z kolcem3 sztuk
Łańcuch żelaznyŁańcuch żelazny1 sztuka
KarabińczykKarabińczyk1 sztuka
Nić skórzanaNić skórzana1 sztuka
Barwnik do skóryBarwnik do skóry1 sztuka

Potrzebne narzędzia:

Nóż do skóryNóż do skóry
BigownicaBigownica
Dziurkacz do skóryDziurkacz do skóry
SzydłoSzydło
Dwie igły rymarskieDwie igły rymarskie
12

Make the belly-band

Cut it 3 in wide and 3 ft 8 in long, narrowed to 2 in for 6 in at both ends, with a buckle hole about 3 in from the point. Make two billets 2 ft 2 in x 2 in and two loops about 1¾ in wide; edge, crease and black everything. Prick the billets six per inch for about 6 in from the shaved end, set the buckle with the billet lapping 3 in over it and the loop about 1 in from the buckle, tack and stitch with six-cord black-wax thread, twice waxed, with two or three stitches in the centre of each end. Open and crease the loops and make four holes in the billets.

Materiały do tego kroku:

Skóra uprzężowaSkóra uprzężowa1 sztuka
Żelazna klamra z kolcemŻelazna klamra z kolcem2 sztuk
Nić skórzanaNić skórzana1 sztuka
Barwnik do skóryBarwnik do skóry1 sztuka

Potrzebne narzędzia:

Nóż do skóryNóż do skóry
Fazownik krawędziFazownik krawędzi
BigownicaBigownica
Przecinak do szycia skóryPrzecinak do szycia skóry
Dziurkacz do skóryDziurkacz do skóry
SzydłoSzydło
Dwie igły rymarskieDwie igły rymarskie
Kozioł rymarskiKozioł rymarski
13

Troubleshooting

Crupper and breeching troubleshooting.

Flow

Loading...
14

History and honest limits

From **Harness Making**, edited by Paul N. Hasluck, Cassell and Company, 1904, chapter VII, "Cart Saddles, Reins, etc." (Project Gutenberg #70169). All sizes are his. Not made here: the iron-dee crupper he gives as a matter of taste, the ornamental breast-plate, the maker's-name stamp, and the final coat of "Harris's liquid or composition", a trade dressing. The heat source for the iron and the metric figures are ours.

Materiały

12

Wymagane narzędzia

16

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...