Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Hot Plate Magnetic Stirrer: Ring Heater over a Relay Magnet on a Shielded Spindle (Hug, US 3,028,476)
Ed

Autor

Ed

9. listopad 2026FI
11
0
0
0
0

Hot Plate Magnetic Stirrer: Ring Heater over a Relay Magnet on a Shielded Spindle (Hug, US 3,028,476)

A laboratory stand that heats a vessel and stirs it at the same time. A motor in the base spins a bar magnet; in Theodore Hug's design (US 3,028,476, 1962) that magnet turns a second, free bar magnet on a spindle inside the hot plate, which in turn spins a coated stirring bar in the vessel. A stainless-steel radiation shield and an air gap keep the ring heater's heat away from the motor. The relay magnet sits about 1/2 in. under the aluminium heat sink: closer, eddy currents in the sink slow the stirring. Source: T. Hug, "Hot Plate and Magnetic Stirrer", US Patent 3,028,476 (filed 1960, granted 1962). Picture: its Figs. 1-2.
Zaawansowany
Unknown

Instrukcje

1

Read Hug

"Attempts have been made to couple conventional heating means to magnetic stirrers, but the same have proved to be unsuccessful. Thus, the base of a laboratory vessel must be positioned relatively close to the driving rotating magnet ... Moreover, if an appreciable amount of heat from the heating means is transmitted to the motor of the magnetic stirrer, it will drastically reduce the useful operating life of said motor."
2

Build the stirrer base

Make a housing of aluminium (or another non-magnetic material) and mount an electric motor inside with its shaft upright. Fix a permanent bar magnet horizontally on the top of the shaft, just under the housing top. Wire the motor through a rheostat to its cord so the speed can be varied. Sizes, motor rating and how the housing is formed are not given.

Materiały do tego kroku:

Blacha aluminiowaBlacha aluminiowa1 housing
Silnik elektrycznySilnik elektryczny1 sztuka
Zestaw magnesów sztabkowychZestaw magnesów sztabkowych1 drive magnet
ReostatReostat1 sztuka
Przewód giętki z wtyczkąPrzewód giętki z wtyczką1 sztuka

Potrzebne narzędzia:

Nieznane wymiaryNieznane wymiary
Nieznana metoda kształtowaniaNieznana metoda kształtowania
3

Make the radiation shield

Shape a radiation shield of non-magnetic stainless steel so it straddles the top of the housing, on stainless-steel legs (a poor conductor of heat) that stand on the housing top. Bore its centre and fit a threaded spindle there with a nut on each side of the shield. Tap a blind thread in each leg.

Materiały do tego kroku:

Blacha ze stali nierdzewnej - 304Blacha ze stali nierdzewnej - 3041 shield and legs
Pręt gwintowanyPręt gwintowany1 spindle
Nakrętka sześciokątnaNakrętka sześciokątna2 sztuk

Potrzebne narzędzia:

Nożyce do blachyNożyce do blachy
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Zestaw do gwintowaniaZestaw do gwintowania
Nieznana metoda kształtowaniaNieznana metoda kształtowania
4

Fit the relay magnet

Bore a blind cavity in a hub of non-magnetic material so it turns freely on the spindle. Lay a permanent bar magnet 1/4 in. by 1 in. by 1 3/4 in. on top of the hub and hold it with a strap screwed to the hub. The hub and strap material is not given.

Materiały do tego kroku:

Zestaw magnesów sztabkowychZestaw magnesów sztabkowych1 relay magnet, 1/4 x 1 x 1 3/4 in.
Nieznany materiałNieznany materiał1 hub and strap
Śruby maszynoweŚruby maszynowe2 sztuk

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Zestaw do gwintowaniaZestaw do gwintowania
5

Mount the supports

Make three support members of non-magnetic stainless steel, each an upright with flanges. Screw the flanges down into the legs, with small tubular spacers of insulating material round the screws between the shield and the flanges, so air can circulate and carry heat away. Fit a grommet in one support for the heater cord. The spacer material is not given.

Materiały do tego kroku:

Blacha ze stali nierdzewnej - 304Blacha ze stali nierdzewnej - 3041 three supports
Śruby maszynoweŚruby maszynowe3 sztuk
Nieznany materiał izolacyjnyNieznany materiał izolacyjny3 tubular spacers

Potrzebne narzędzia:

Nożyce do blachyNożyce do blachy
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
6

Fit the heater and top

Mount an annular ring heater (elements in a non-magnetic sheath) coaxial with the spindle; join its cord wires to its threaded stud between two nuts. Above it lay an aluminium heat sink, a flat plate wider than the heater, so the relay magnet is about 1/2 in. below it. Cover with a top plate of aluminium or stainless steel whose edge is spun into an inverted dish, and screw the edge to the tops of the supports. The patent claims a blackened outer surface on the heat sink and top plate (how is not given). In use, set the hot plate on the stirrer and put a stirring bar (a short bar magnet sealed in glass or coated with PTFE) in the vessel: the drive magnet turns the relay magnet, which turns the bar.

Materiały do tego kroku:

Element grzejnyElement grzejny1 ring heater
Przewód giętki z wtyczkąPrzewód giętki z wtyczką1 sztuka
Nakrętka sześciokątnaNakrętka sześciokątna2 sztuk
Płyta aluminiowaPłyta aluminiowa1 heat sink
Blacha aluminiowaBlacha aluminiowa1 top plate
Śruby maszynoweŚruby maszynowe3 sztuk

Potrzebne narzędzia:

Narzędzie do wyoblaniaNarzędzie do wyoblania
Tokarka do metaluTokarka do metalu
Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł

Materiały

13

Wymagane narzędzia

8

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...