Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Iron Tube: Butt-Welded by Drawing Through Dies on a Draw Bench (Whitehouse, 1825)
Forge

Autor

Forge

4. listopad 2026NO
13
0
0
1
0

Iron Tube: Butt-Welded by Drawing Through Dies on a Draw Bench (Whitehouse, 1825)

Cornelius Whitehouse's way of making welded iron tubes, the basis of butt-weld pipe ever since: a strip of flat iron is turned up into a tube with its edges meeting, heated nearly to fusion in a hollow fire, and pulled by the chain of a draw bench through a pair of dies, which press the hot edges together and weld them. The tube is welded in two halves, one end at a time. Whitehouse made tubes 2 to 8 ft long in one piece, smooth inside and out. Unknown: plate thickness, width and tube sizes. The source does not give them. Source: Whitehouse's specification of 1825, quoted in C. D. Terry, Butt Weld Pipe (1907). Picture: Terry's Figs. 4 and 5.
Zaawansowany
Unknown

Instrukcje

1

Turn the plate over

Take a piece of flat iron (plough-plate iron) of a thickness and width to suit the intended bore. Bend up its sides ('turn it over') until the edges meet, or nearly so, and it forms a long tube. Ours: hammer and anvil for the bending.

Materiały do tego kroku:

Pręty żelaza kutegoPręty żelaza kutego1 flat plough-plate iron
Nieznane wymiaryNieznane wymiary1 sztuka

Potrzebne narzędzia:

Młot kowalskiMłot kowalski
Kowadło płaskieKowadło płaskie
2

Heat in the hollow fire

Put the tube into a hollow fire, urged by a blast, and heat it until the iron is on the point of fusion. Ours: a smith's forge as the hollow fire.

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Kleszcze kowalskieKleszcze kowalskie
3

Draw it through the dies

Clamp the end of the tube to the chain of the draw bench, driven by a hand winch or an engine. Draw it out of the fire through a pair of dies of the size wanted, set in a screw press and closed to their bearing, so that the hot edges are pressed together and welded. A pair of pinchers with a conical hole, held against a standard, may be used instead of the press and dies.

Potrzebne narzędzia:

Ciągarka ławowaCiągarka ławowa
Kleszcze kowalskieKleszcze kowalskie
4

Weld the other half

Open the clamp and take the tube off. Grip the other end, put the unwelded part into the fire, heat it, and draw it through the dies in the same way.

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Ciągarka ławowaCiągarka ławowa
Kleszcze kowalskieKleszcze kowalskie

Materiały

2

Wymagane narzędzia

5

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...