Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Lead Came: Window Rods Cast in a Hinged Iron Mould (Theophilus, tr. Hendrie 1847)
Forge

Autor

Forge

4. listopad 2026NO
8
0
0
1
0

Lead Came: Window Rods Cast in a Hinged Iron Mould (Theophilus, tr. Hendrie 1847)

The lead rods that hold the pieces of a medieval glass window, cast the way Theophilus describes around 1100: pure lead is poured with a warm iron spoon into a hinged iron mould with grooves hollowed down both halves, knocked out, and the mould closed again for the next. Kept at an even heat, one heating of the mould casts more than forty rods. Source: Theophilus, De Diversis Artibus, Book II, ch. XXIII-XXV, tr. R. Hendrie (1847), pp. 147-149. Picture: p. 149.
Średniozaawansowany
Unknown

Instrukcje

1

Make the iron mould

Take two irons two fingers broad, one finger thick and a yard long. Hinge them together at one end with a nail; make the other end a little wider and thinner to form the pouring mouth. File them until no light shows between them. Rule two lines down the middle of each, hollow the groove between them with a chasing iron as deep as you wish and rasp it a little, so that the lead poured in makes one piece.

Potrzebne narzędzia:

Forma do ołowianych prętów witrażowychForma do ołowianych prętów witrażowych
2

Melt the lead

Make a hearth with a hollow for a large earthen vessel lined inside and out with clay beaten up with dung, and dry it with a big fire. Put pure lead on the fire over the vessel so that it runs into it as it melts.

Materiały do tego kroku:

Wlewek ołowiuWlewek ołowiu1 pure lead

Potrzebne narzędzia:

Garnek glinianyGarnek gliniany
Węgiel drzewnyWęgiel drzewny
3

Cast the rods

Warm the open mould on the charcoal, close it and set it in the slot of a yard-long wooden holder standing on the ground. Pour the lead in with a small warmed iron spoon, keeping the spoon on the fire between pours. Knock the mould out, open it with a knife, take out the rod, close it and cast again. If the lead does not reach the bottom, warm the mould more. At an even heat you can cast more than forty rods.

Potrzebne narzędzia:

Forma do ołowianych prętów witrażowychForma do ołowianych prętów witrażowych
ChochlaChochla
Nóż introligatorskiNóż introligatorski
Węgiel drzewnyWęgiel drzewny

Materiały

1

Wymagane narzędzia

5

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...