Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Plastic Extruder: Steam-Jacketed Screw Stuffer with a Heated Nozzle (Andersen & Strasdin, US 2,384,521, 1945)
Emma

Autor

Emma

3. listopad 2026SE
7
0
0
0
0

Plastic Extruder: Steam-Jacketed Screw Stuffer with a Heated Nozzle (Andersen & Strasdin, US 2,384,521, 1945)

A screw extruder for thermoplastics: a turning screw in a steam-jacketed barrel pushes hot, softened plastic forward through a short nozzle heated electrically. The barrel is kept a little below the plastic's flow temperature and the nozzle well above it, so the extruded rod comes out with a smooth, glass-like skin. Result: an extruder that makes rod, tube or strip at 25 to 30 feet a minute. Source: B. Andersen and R. F. Strasdin (Celanese), US 2,384,521 (1945). Unknown: sizes and metals. Picture: the patent drawing.
Zaawansowany
Unknown

Instrukcje

1

Make the screw

Turn a screw to fit the barrel. Its thread may be single or double; to press the plastic harder toward the nozzle, make the pitch increase or the groove get shallower toward that end. Example: a double-thread screw. Ours: mild steel. Not given: sizes.

Materiały do tego kroku:

Pręt okrągły ze stali niskowęglowejPręt okrągły ze stali niskowęglowej1 screw

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
FrezarkaFrezarka
Nieznane wymiaryNieznane wymiary
2

Make the jacketed barrel

Make the barrel with a steam jacket round it and a steam port into the jacket, and a feed throat at the back end. The inside wall may be grooved, pitched so that every flight of the screw always meets a groove; this stops the plastic slipping. Not given: the metal, the steam pressure.

Materiały do tego kroku:

Nieznany metalNieznany metal1 barrel and jacket

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
Nieznane wymiaryNieznane wymiary
3

Fit the heated nozzle

At the front, fit a streamlined nozzle head so no plastic can pocket and decompose, and a nozzle 1/2 to 18 inches long; about 6 inches in the example. Perforated plates may go between the screw and the nozzle. Heat the nozzle with an electric resistance coil. Ours: nichrome wire.

Materiały do tego kroku:

Nieznany metalNieznany metal1 nozzle head and nozzle
Drut oporowy nichromowyDrut oporowy nichromowy1 nozzle heating coil
Nieznany materiał izolacyjnyNieznany materiał izolacyjny1 coil insulation

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
4

Drive the screw

Drive the screw through a gear from a motor, so its speed can be kept steady; 20 revolutions a minute in the example. Not given: the drive.

Materiały do tego kroku:

Silnik elektrycznySilnik elektryczny1 drive motor
Nieznany metalNieznany metal1 drive gears

Potrzebne narzędzia:

Nieznane wymiaryNieznane wymiary
5

Extrude a rod

Keep the barrel 0 to 100 °F below the plastic's flow temperature and the nozzle 50 to 100 °F above it. Example: barrel at about 270 °F by steam, nozzle at about 400 °F, for a cellulose acetate with a flow temperature of 307 °F. Feed the hot, softened plastic into the throat at a steady rate. Carry the rod away on a conveyor and cool it at once with cold water, then cut it to length.

Potrzebne narzędzia:

Kocioł parowyKocioł parowy
PirometrPirometr
WodaWoda

Materiały

5

Wymagane narzędzia

6

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...