Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Profile Gauge: Sliding Pins Held by Cloth-Wrapped Rubber Tubes (Reinhardt, 1918)
Forge

Autor

Forge

13. listopad 2026NO
7
0
0
0
0

Profile Gauge: Sliding Pins Held by Cloth-Wrapped Rubber Tubes (Reinhardt, 1918)

James H. Reinhardt of East Orange, New Jersey, received US 1,261,438, dated 2 April 1918, for a profile gauge: a row of pins clamped between two thin metal members. Rubber tubes wrapped in cloth press on the pins, so each one slides when pushed and stays where it is left. Pressed against an object, the pin ends take its outline, and a pencil drawn along them copies it, so the shape can be made again. We build his single gauge from brass sheet and steel wire. All sizes are ours.
Średniozaawansowany
About 5 hours

Instrukcje

1

How many pins

Wczytywanie notatnika Jupyter…
2

Read US 1,261,438

"The rods or pins 3 of the respective gages may be pushed against the surface of the object, as required, to obtain its outline along the ends of the rods or pins, whereby a pencil may be drawn along the ends of the pins to trace such outline or contour of the object. From such outlines objects corresponding to the master object may be reproduced either in relief or concave according to which way the outline drawn from the ends of the rods is used."
3

Make the two members

Cut two strips of 0.8 mm brass sheet 200 x 32 mm (ours) with tin snips and file the edges. Bend 4 mm down along each long side in the vice, so each strip becomes a shallow channel 24 mm wide: his "gutter-like form". Clamp them together, open sides facing, and drill a 3.5 mm hole through both, 50 mm from each end, on the middle line.

Materiały do tego kroku:

Blacha mosiężnaBlacha mosiężna2 sztuk

Potrzebne narzędzia:

Nożyce do blachyNożyce do blachy
Zestaw pilnikówZestaw pilników
Imadło warsztatoweImadło warsztatowe
Rysik traserskiRysik traserski
Wiertarka ręcznaWiertarka ręczna
4

Make the gutters

Cut two strips of the same brass 180 x 14 mm and bend each round a 6 mm rod into a U that will hold the rubber tube, his gutters 10. Rivet them inside one member, one near each long side, with copper rivets, keeping clear of the screw holes.

Materiały do tego kroku:

Blacha mosiężnaBlacha mosiężna1 sztuka
Nity miedzianeNity miedziane6 sztuk

Potrzebne narzędzia:

Nożyce do blachyNożyce do blachy
Pręt ze stali niskowęglowejPręt ze stali niskowęglowej
Imadło warsztatoweImadło warsztatowe
Wiertarka ręcznaWiertarka ręczna
Młotek ślusarski z kulistym rąbemMłotek ślusarski z kulistym rąbem
5

Make the retainers

Cut two pieces of 6 mm rubber tubing 170 mm long and push a 2 mm wire through each, his cores 9, "to somewhat stiffen them". Wrap each in a strip of cotton cloth, lap its edges and glue them with contact cement, his protecting cloth 12, so the rubber does not touch the metal. Lay one in each gutter.

Materiały do tego kroku:

Wąż gumowyWąż gumowy1 sztuka
Drut stalowyDrut stalowy1 sztuka
Tkanina bawełnianaTkanina bawełniana1 sztuka
Klej kontaktowyKlej kontaktowy1 sztuka

Potrzebne narzędzia:

Obcinaki boczneObcinaki boczne
NożyczkiNożyczki
6

Cut the pins

Cut 1 mm steel wire into pins 120 mm long, as many as the notebook gives. Straighten any that are bent and file both ends flat and smooth, so they slide easily and do not mark the work.

Materiały do tego kroku:

Drut stalowyDrut stalowy1 sztuka

Potrzebne narzędzia:

Obcinaki boczneObcinaki boczne
Zestaw pilników iglakówZestaw pilników iglaków
Imadło warsztatoweImadło warsztatowe
7

Assemble

Lay the member with the retainers open side up. Lay the pins across it side by side, touching, centred so equal lengths stick out on both sides; leave a gap at each screw hole (ours). Put the other member on top and pass a machine screw through each hole with a nut. Tighten them evenly until each pin slides when pushed but does not fall.

Materiały do tego kroku:

Śruby maszynoweŚruby maszynowe2 sztuk
Nakrętka sześciokątnaNakrętka sześciokątna2 sztuk

Potrzebne narzędzia:

Zestaw wkrętakówZestaw wkrętaków
Klucz nastawnyKlucz nastawny
8

Take a profile

Push all the pins level with a flat board. Press the gauge square against the object until the pins have taken its shape. Lift it off, lay it on paper or on the stock to be cut, and draw a pencil along the pin ends.

Potrzebne narzędzia:

OłówekOłówek
9

Troubleshooting

Pin profile gauge troubleshooting.

Flow

Loading...
10

History and honest limits

**James H. Reinhardt** of East Orange, New Jersey, US 1,261,438, dated 2 April 1918, filed 20 June 1914. He claimed "a profile gage comprising a pair of opposed members, rods or pins located between and transversely with respect to said members, means for clamping said members together" and "a resilient retainer comprising spaced rubber tubes". His members can have teeth along their edges, and his patent also covers end castings that join several gauges in a line or at an angle, a smaller gauge clamped between them, a toothed spacer strip and a rubber-mat retainer: none of those are built here. He gives no sizes: the brass, the 200 mm length, the 1 mm pins, the tube and core sizes, the cement, the rivets and the screws are ours.

Materiały

8

Wymagane narzędzia

13

Według tego planu powstaje

Powiązane blueprinty

Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...