Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Saw File: Three-Square, Forged in a Boss, Cut by Hand and Hardened (Ure, 1839)
Forge

Autor

Forge

4. listopad 2026NO
24
0
0
0
0

Saw File: Three-Square, Forged in a Boss, Cut by Hand and Hardened (Ure, 1839)

The file for sharpening saw teeth as Sheffield made it by hand: a three-square (triangular) bar of cast steel, not tapering, forged in a V-shaped boss, its teeth cut one by one with a chisel and hammer, then hardened under a coat of animal carbon and salt and quenched in cold spring water. Ure says saw files in particular should be hardened with the carbon mixture, so they will cut iron and steel. Not given: sizes and teeth per inch. Source: A. Ure, Dictionary of Arts, Manufactures, and Mines (1839), File. Picture: our drawing.
Zaawansowany
Unknown

Instrukcje

1

Forge the blank

Draw cast steel out square at the forge, then lay it with one angle down in a boss whose recess has two sides meeting at an angle, so the hammer forms one side and the boss the other two. Keep it the same size along its length (saw files are not tapered).

Materiały do tego kroku:

Stal tyglowaStal tyglowa1 cast steel bar
Nieznane wymiaryNieznane wymiary1 sztuka

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Kleszcze kowalskieKleszcze kowalskie
Dolna matryca kowalska (sztanca dolna)Dolna matryca kowalska (sztanca dolna)
MłotekMłotek
Młot dwuręcznyMłot dwuręczny
2

Cut the teeth

On an anvil with a flat, even face, hold the file down with a leather strap over each end, the workman's feet in the straps like stirrups. Cut the teeth with a chisel a little broader than the file, sharpened to about 20 degrees, struck with a hammer of 1 to 6 lb. For single cut, run a fine file lightly over the teeth to take off the roughness; for double cut, cut a second set nearly at right angles to the first.

Potrzebne narzędzia:

Kowadło staloweKowadło stalowe
Rzemień skórzanyRzemień skórzany
Przecinak ślusarskiPrzecinak ślusarski
MłotekMłotek
Pilnik do metaluPilnik do metalu
3

Cut the other sides

To cut the next side, lay the file in a piece of lead-tin alloy with an angular groove, so the teeth already cut are not spoiled on the anvil.

Potrzebne narzędzia:

Lut cynowo-ołowiowyLut cynowo-ołowiowy
Kowadło staloweKowadło stalowe
Przecinak ślusarskiPrzecinak ślusarski
MłotekMłotek
4

Coat for hardening

Distil shoemakers' and curriers' leather refuse in an iron still and powder the bright coal left. Grind about equal parts by bulk of this carbon and salt to the consistence of cream with water and cover the file with it.

Potrzebne narzędzia:

Retorta żelaznaRetorta żelazna
SólSól
WodaWoda
5

Harden

Hold the file by the tang in a fire of very small cokes, drawing it out often, until it is an even cherry red from tang to point. Plunge it straight down, quickly, into clear spring water as cold as possible.

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Koks hutniczyKoks hutniczy
Kleszcze kowalskieKleszcze kowalskie
WodaWoda
6

Clean and oil

Brush the file with water and powdered cokes until clean and metallic, wash it in two or three waters to take off all the salt, dip it in lime-water, dry it quickly before the fire and oil it while warm with olive oil containing a little oil of turpentine.

Potrzebne narzędzia:

Koks hutniczyKoks hutniczy
WodaWoda
Woda wapiennaWoda wapienna
Oliwa z oliwekOliwa z oliwek
TerpentynaTerpentyna

Materiały

2

Wymagane narzędzia

17

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...