Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Soldering Station: a Stand Whose Bimetal Switch Reads the Iron's Heat (Birk, Hart Mfg., US 2,248,486, 1941)
Ed

Autor

Ed

3. listopad 2026FI
4
0
0
0
0

Soldering Station: a Stand Whose Bimetal Switch Reads the Iron's Heat (Birk, Hart Mfg., US 2,248,486, 1941)

A soldering station: an ordinary electric iron plugs into its stand, and the stand controls it. When the iron is laid in the stand's trough, its heater housing sits over a flue with a U-shaped bimetal switch inside; the heat it gives off opens the switch at the temperature you set with a screw, and closes it again as it cools. A red lamp shows the iron heating, a green lamp shows it hot and idling. Result: a stand that keeps an electric iron at a set temperature between jobs and shows its state. Source: H. W. Birk (Hart Manufacturing), US 2,248,486 (1941). Unknown: sizes, the bimetal, the lamps. Picture: the patent drawing.
Średniozaawansowany
Unknown

Instrukcje

1

Make the stand

Cast or form a box-shaped stand in one piece from a fire-resistant material such as porcelain: a high front wall, a low back wall, two side walls and a top sloping down about 10° toward the back, with feet at the corners so air can pass beneath. Close the bottom with a removable plate screwed to a flange and pierced with air holes. In the top, hollow a trough shaped to the iron's heater housing, ending at a shoulder, then a narrower groove for the tip. Cut a flue through the top along the trough, under a cover with holes. Ours: porcelain. Not given: sizes.

Materiały do tego kroku:

Nieznany materiałNieznany materiał1 porcelain stand
Nieznany metalNieznany metal1 bottom plate, screws

Potrzebne narzędzia:

Nieznane wymiaryNieznane wymiary
2

Fit the bimetal switch

Bend a strip of bimetal into a U whose legs spread apart when cool and close together when hot. Rivet one leg to a metal strip fixed beside the flue (on an insulating bracket if the stand conducts); put a contact on the free leg's end. Face it with a fixed contact on a screw stud threaded through a metal plate and out through the side wall in an insulating sleeve, slotted for a screwdriver: turning it sets the temperature, low for wax melting or high for electric branding irons. Not given: the bimetal, the contact metal.

Materiały do tego kroku:

Pasek bimetalicznyPasek bimetaliczny1 sztuka
Nieznany metalNieznany metal1 strips, plate, contacts, stud
Nieznany materiał izolacyjnyNieznany materiał izolacyjny1 bracket, sleeve, plate

Potrzebne narzędzia:

Zestaw nitowniczyZestaw nitowniczy
Zestaw do gwintowaniaZestaw do gwintowania
3

Wire the outlet and lamps

Set an outlet in a side wall for the iron's plug, held by a flange and a split ring, and wire it in series with the switch to the supply cord. At the top of the front wall, set two lamp sockets at about 45°, one with a red lens and one with a green: wire the red in parallel with the iron's heater, the green in parallel with the switch. Not given: the lamp ratings, the outlet type.

Materiały do tego kroku:

Nieznane złączeNieznane złącze1 outlet
Oprawka żarówkiOprawka żarówki2 sztuk
ŻarówkaŻarówka2 sztuk
Nieznany materiałNieznany materiał2 red and green lenses
Przewód giętki z wtyczkąPrzewód giętki z wtyczką1 sztuka

Potrzebne narzędzia:

Zestaw wkrętakówZestaw wkrętaków
4

Use it

Set the temperature by turning the slotted stud with a screwdriver. Plug an electric soldering iron into the stand's outlet and lay it in the trough so its heater housing closes the flue. While the bimetal is cool the switch is closed and the red lamp lights: the iron heats. At the set temperature the switch opens; the green lamp glows, the red goes dark and the iron idles. Lift the iron off and air rushes up the flue, cooling the bimetal so the iron heats again. Because it senses the heater, not the tip, the heater cannot burn out even if the tip is loose.

Materiały do tego kroku:

LutownicaLutownica1 electric soldering iron

Potrzebne narzędzia:

Zestaw wkrętakówZestaw wkrętaków

Materiały

9

Wymagane narzędzia

4

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...