Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Solderless Breadboard: Cantilever Contacts in a Moulded Acetal Housing (Tengler, US 4,420,215)
Ed

Autor

Ed

4. listopad 2026FI
11
0
0
0
0

Solderless Breadboard: Cantilever Contacts in a Moulded Acetal Housing (Tengler, US 4,420,215)

A breadboard lets you build a circuit without solder: push component leads into holes and spring contacts underneath join them in rows. John N. Tengler of A P Products received US 4,420,215 (1983) for one: a one-piece moulded acetal housing with holes on 0.100 in centres, and sets of three springy cantilever contacts of copper alloy No. 688 pushed in from below. Not given: the contact thickness and sizes, how the contacts are formed, and the moulding conditions. Source: J. N. Tengler, US 4,420,215. Picture: the patent's drawing sheet.
Zaawansowany
Not given in the source

Instrukcje

1

Mould the housing

Injection-mould the housing as one piece in acetal copolymer (Tengler names CELCON). His example has 78 cells in 26 rows of three, open at the bottom, under a top wall whose holes sit on 0.100 in centres. Give each cell two preload bars on its front wall, one either side of the hole, with tapered lower ends. Mould notches into the walls between the cells of a row, and none into the front and back walls, so a contact set fits only the right way round.

Materiały do tego kroku:

Granulat kopolimeru acetalowegoGranulat kopolimeru acetalowego1 one housing

Potrzebne narzędzia:

WtryskarkaWtryskarka
Rama formy wtryskowejRama formy wtryskowej
Nieznane wymiaryNieznane wymiary
2

Form the contact sets

Form three identical contacts from copper alloy No. 688, joined at the foot by a strip. Each is a single cantilever: a foot with a seat, an arm curving up into a spring, a hairpin bend, then a contact face that a pushed-in lead slides along, ending in a tip, with a stop extension that comes to rest against the arm. If you like, stamp a small barb in the joining strip.

Materiały do tego kroku:

Taśma ze stopu miedzi 688Taśma ze stopu miedzi 6881 one set of three per row

Potrzebne narzędzia:

Nieznana metoda kształtowaniaNieznana metoda kształtowania
Nieznane wymiaryNieznane wymiary
3

Push the sets in from below

Push each set up into its row from the open bottom, contact faces toward the holes, with the strip running through the notches. The strip is bent at a slight angle, so the front wall springs it and wedges the contact's foot against the back wall. The preload bars press on the contact face, and the barb, if there is one, bites into the plastic.

Potrzebne narzędzia:

Szczypce płaskieSzczypce płaskie
4

Check a row

Push a resistor lead through a hole: it should slide along the contact face. The two end contacts of a row join two components; Tengler meant the middle one for injecting or testing a signal. Check with a meter that the three holes of a row connect and neighbouring rows do not.

Potrzebne narzędzia:

Opór elektrycznyOpór elektryczny
MultimetrMultimetr

Materiały

2

Wymagane narzędzia

7

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...