Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Alcohol Burner: the Glass Spirit Lamp with a Copper Wick Shield (Morfit, 1849)
Charlie

Autor

Charlie

7. listopad 2026DE
15
0
0
0
0

Alcohol Burner: the Glass Spirit Lamp with a Copper Wick Shield (Morfit, 1849)

A small glass lamp that burns alcohol for heating test tubes and small vessels on the bench. Campbell Morfit (1849): the glass body holds the alcohol; a round copper shield with a tube in its centre carries a cotton wick and rests on the neck; a minute hole in the shield lets vapour escape; a glass cap ground to fit the neck keeps the alcohol from evaporating. Alcohol gives no smoke and does not blacken the glass. Sizes, and how the wick tube is fixed, are not given. Source: C. Morfit, Chemical and Pharmaceutic Manipulations (1849), pp. 160-162. Picture: Fig. 115.
Początkujący
Unknown

Instrukcje

1

Read Morfit

"To the neck b is adjusted a copper circular shield c, with a tube in its centre for the passage of the wick, which should be of cotton, and similar to that used for tallow candles. The shield should rest upon, rather than within the neck, otherwise its expansion by the heat may cause the breakage of the glass. A minute opening drilled in the shield is also requisite for the escape of vapor in case the alcohol should become heated."
2

Make the copper shield

Cut a round copper shield a little wider than the neck of the glass body, so it rests on the neck and not inside it. Fix a short copper tube through its centre for the wick (ours: soldered; the joint is not given). Drill a minute hole in the shield for vapour to escape. Sizes are not given (unknown).

Materiały do tego kroku:

Blacha miedzianaBlacha miedziana1 shield
Rura miedzianaRura miedziana1 wick tube
Lut cynowo-ołowiowyLut cynowo-ołowiowy1 joint
TopnikTopnik1 joint

Potrzebne narzędzia:

Nożyce do blachyNożyce do blachy
LutownicaLutownica
Wiertarka ręcznaWiertarka ręczna
Nieznane wymiaryNieznane wymiary
3

Fit the wick and the body

Draw a cotton wick of the tallow-candle kind through the tube so it reaches down into the glass body, which is the alcohol reservoir. Set the shield on the neck. Ours: a clear glass bottle as the body.

Materiały do tego kroku:

Butelka szklana (bezbarwna)Butelka szklana (bezbarwna)1 body
Knot bawełniany do świecKnot bawełniany do świec1 sztuka

Potrzebne narzędzia:

Nożyce do blachyNożyce do blachy
4

Fit the glass cap

Cover the wick, when the lamp is not in use, with a glass cap ground inside to fit the neck closely. It stops the alcohol evaporating and the wick taking up water, which makes relighting difficult. Put it on only after the lamp is out. How the cap is made and ground is not given (unknown).

Materiały do tego kroku:

Nieznane szkłoNieznane szkło1 cap

Potrzebne narzędzia:

Nieznane wymiaryNieznane wymiary
5

Fill and use

Morfit burns alcohol of about specific gravity 0.85. Always put the lamp out before refilling, then pour the spirit in gently until the reservoir is nearly full. The flame is hottest just below its tip; bring the vessel to it gradually, and spread the heat with copper gauze between flame and vessel for larger surfaces.

Materiały

7

Wymagane narzędzia

4

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...