Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)
Woody

Autor

Woody

13. listopad 2026NO
7
0
0
0
0

16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)

Stillman Taylor's open Canadian canoe from The Boy Mechanic, Book 3 (1919): about 16 ft long, 31 in beam, 60 to 70 lb. Built upside down over a backbone and seven paper-pattern molds, with oak or ash stems, keelson and gunwales, 1/8 in cedar ribs and planking fastened with copper clout nails, then covered with No. 6 canvas laid in melted marine glue, painted, and varnished. Every layout dot and width is his, as printed.
Zaawansowany
Several weeks

Instrukcje

1

His layout data

Wczytywanie notatnika Jupyter…
2

Read The Boy Mechanic, Book 3

"Working with light materials, the canoe builder must pay particular attention to the workmanship ... the work must not be hurried, but plenty of time taken to do each and every part well."
3

Get the materials

Stem: oak or ash 6 ft x 3/4 in square. Keelson: oak or ash 14 ft x 3-1/2 x 3/8 in. Gunwales: 2 of oak or ash 16 ft x 7/8 x 1/2 in. Seat risings: 2 of oak or ash 1/2 in square. Fenderwales: 34 ft of 1/2 in half-round molding. Outside keel (optional): oak 14 ft x 1 x 1/2 in. Deck beams: 2 of oak or ash 8 x 1-1/8 x 3/8 in. Seat frames: 2 at 30 x 3 x 3/4 and 2 at 12 x 2-1/4 x 3/4 in. Planking: cedar or pine, 100 sq ft, 1/8 in (25 ft of 1 in lumber dressed to 1/8 in, in 12, 14 and 16 ft lengths). Ribs: 360 running ft of cedar 1-3/4 x 1/8 in. Breast hooks: cedar or oak 32 x 9 x 3/4 in. Backbone, molds and ribbands from any cheap stuff. Fastenings: 1 lb 2 in wire nails; 1 lb 5/8 in and 1/2 lb 3/4 in copper clout nails; 18 brass screws 1-1/4 in No. 8 and 24 brass screws 1 in No. 6; 4 lb marine glue; 3 oz No. 2 copper tacks; 11-3/4 yd No. 6 canvas; 1 lb 3/8 in copper tacks. Rock elm or fir may replace oak or ash; spruce, pine, cypress or fir may replace cedar.

Materiały do tego kroku:

Deska z dębu białegoDeska z dębu białego4 sztuk
Deska cedrowaDeska cedrowa6 sztuk
Deska sosnowaDeska sosnowa3 sztuk

Potrzebne narzędzia:

Piła wzdłużnaPiła wzdłużna
Piła ręcznaPiła ręczna
Strug ręcznyStrug ręczny
Miara zwijanaMiara zwijana
4

Lay out the backbone and molds

Cut the backbone from a 16 ft x 4 x 7/8 in board, top edge 15 ft 8-3/4 in, and mark the mold stations from each end: 22-1/4 in to mold 1, then 23-1/4 in to mold 2 and 23-1/4 in to mold 3, each mold space 3/4 in thick; mold 4 sits at the centre; cut the ends off on the bevel (Fig. 1). Draw each mold on stiff paper from his rectangles, mortises and dots (notebook), trace the curve through the dots, cut out the half, fold and draw the other side, and cut the molds from 7/8 in stock: seven in all, numbered alike from each end: two No. 1, two No. 2 (each in halves), two No. 3 and one No. 4; nail battens across the halves.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa2 sztuk
Arkusze grubego papieruArkusze grubego papieru1 sztuka
GwoździeGwoździe1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Piłka włosowaPiłka włosowa
LinijkaLinijka
OłówekOłówek
NożyczkiNożyczki
MłotekMłotek
5

Bend the stems and shape the keelson

Make the stem mold from his Fig. 6 pattern (24-1/2 x 12 in rectangle, dots in the notebook) and bend the straight-grained 3/4 in square oak or ash stems on it. Cut the keelson 13 ft 11 in long, tapering from 3-1/2 in at the centre: 3-1/2 in at 1 and 2 ft, 3-1/4, 2-5/8, 2 and 1-1/4 in at 3 to 6 ft, and 15/16 in at the ends (Fig. 7). Fasten each stem to the keelson with a couple of 3/4 in No. 10 screws.

Materiały do tego kroku:

Deska z dębu białegoDeska z dębu białego2 sztuk
Wkręty do drewna mosiężneWkręty do drewna mosiężne4 sztuk

Potrzebne narzędzia:

OśnikOśnik
Strug ręcznyStrug ręczny
Piła ręcznaPiła ręczna
Świder korbowy z wiertłemŚwider korbowy z wiertłem
Wkrętak płaskiWkrętak płaski
Ścisk typu CŚcisk typu C
6

Set up the frame

Build it upside down: set the backbone on boxes about 1 ft or more off the floor and the molds in their numbered places, the backbone resting in their top mortises. True the molds with a square and toenail them. Lay the keelson in its mortises, fit the stems to the backbone angle and nail through the mold tops into them. Bevel the stem splice from the inside, leaving the outer edge about 1/8 in wide. Put on the gunwales at the sheer line with nails left proud, then four ribbands a side at 5 in centres from the keel, fastened with 1-1/4 in brads.

Materiały do tego kroku:

Deska z dębu białegoDeska z dębu białego2 sztuk
Deska sosnowaDeska sosnowa1 sztuka
GwoździeGwoździe1 sztuka

Potrzebne narzędzia:

Kątownik stolarskiKątownik stolarski
MłotekMłotek
DłutaDłuta
Strug ręcznyStrug ręczny
7

Rib the hull

Saw cedar ribs 1-3/4 in wide and 1/8 in thick, cut to length gunwale to gunwale over the ribbands. Space them 3 in apart on centres along the keelson, one over each mold. Fasten each rib to the outside of the keelson with two 5/8 in copper clout nails, spring it in under the ribbands and fasten it to the gunwales. Then remove the ribbands.

Materiały do tego kroku:

Deska cedrowaDeska cedrowa2 sztuk
Gwoździe miedziane z szerokim łbemGwoździe miedziane z szerokim łbem1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
MłotekMłotek
Miara zwijanaMiara zwijana
8

Plank the hull

Plank with 1/8 in cedar, bent cold, full length stem to stem, butted edge to edge without bevel, about 3 in wide; begin with the garboard strake at the keel and end with the sheer strake level with the gunwale. Punch nail holes with an awl, staggered along the ribs; clamp the plank, drive copper clout nails and clinch them inside on a clinch iron. Trim the plank ends to the stems and gunwales, saw the backbone in two to take out the frame, tack strips across the gunwales against sagging, and nail where the molds were.

Materiały do tego kroku:

Deska cedrowaDeska cedrowa4 sztuk
Gwoździe miedziane z szerokim łbemGwoździe miedziane z szerokim łbem1 sztuka
Pinezki miedziane (ćwieki)Pinezki miedziane (ćwieki)1 sztuka

Potrzebne narzędzia:

SzydłoSzydło
Ścisk typu CŚcisk typu C
Żelazo do zaginania gwoździŻelazo do zaginania gwoździ
MłotekMłotek
Piła ręcznaPiła ręczna
9

Fit risings, seats, decks and thwarts

Nail 1/2 in square oak or ash seat risings, 14 ft long, about 4 in below the gunwale, boring first and clinching inside. Make the seat frames as Fig. 10 and cane them or tack on canvas (a kneeling paddler may use a 4 or 5 in seat bar instead). Notch the 8 x 1-1/8 x 3/8 in deck beams to wedge about 1/2 in against the gunwales (Fig. 11) and fix each with a 1-1/4 in No. 10 screw through the gunwale. Shape the decks 16 x 8 in (Fig. 12) and fix them with three 1-1/4 in No. 10 screws into the beam and three along each gunwale. Screw a centre thwart of oak or ash, 3/8 in thick, 2 in tapering to 1 in, under the gunwales amidships; extra thwarts behind the forward seat and about 3 ft forward of the rear seat stiffen it.

Materiały do tego kroku:

Deska z dębu białegoDeska z dębu białego2 sztuk
Deska cedrowaDeska cedrowa1 sztuka
Gwoździe miedziane z szerokim łbemGwoździe miedziane z szerokim łbem1 sztuka
Wkręty do drewna mosiężneWkręty do drewna mosiężne30 sztuk
Płótno bawełnianePłótno bawełniane1 sztuka

Potrzebne narzędzia:

Świder korbowy z wiertłemŚwider korbowy z wiertłem
Wkrętak płaskiWkrętak płaski
Piła ręcznaPiła ręczna
DłutaDłuta
MłotekMłotek
10

Lay the canvas

Lay the No. 6 canvas smoothly on the hull and trim it to fold at the stems (Fig. 13). Melt the black marine glue in a can over a moderately hot fire and spread a fairly heavy coat over one side of the canvas with a stiff brush. Lay it on and iron it with a moderately hot flatiron so the glue melts into the planking. Tack the edges along the gunwales and fold the canvas smoothly at the stems, tacking exactly down the stem centre line.

Materiały do tego kroku:

Płótno bawełnianePłótno bawełniane1 sztuka
Klej szkutniczyKlej szkutniczy1 sztuka
Pinezki miedziane (ćwieki)Pinezki miedziane (ćwieki)1 sztuka

Potrzebne narzędzia:

Puszka blaszanaPuszka blaszana
Pędzel szerokiPędzel szeroki
Żelazko płaskieŻelazko płaskie
NożyczkiNożyczki
MłotekMłotek
11

Fenders, stem bands and keel

Tack 1/2 in round molding over the canvas edge (or a 1 in strip of planking with 1-1/4 in brads every 2 or 3 in). Put on stem bands of wood about 3/8 in square, rounded, with 1-1/4 in brads, or better, 3/8 in brass oval stem band with 3/4 in screws. An outside keel is optional: about 1 x 1/2 in of oak or ash tapered to the stem bands, or a flat keel about 2-1/2 in wide of 3/8 in oak or ash, which turns more easily and guards the bottom.

Materiały do tego kroku:

Listwa drewniana półokrągłaListwa drewniana półokrągła1 sztuka
Mosiężna listwa dziobnicyMosiężna listwa dziobnicy2 sztuk
Wkręty do drewna mosiężneWkręty do drewna mosiężne12 sztuk
Deska z dębu białegoDeska z dębu białego1 sztuka
GwoździeGwoździe1 sztuka

Potrzebne narzędzia:

MłotekMłotek
Wkrętak płaskiWkrętak płaski
Strug ręcznyStrug ręczny
Wiertarka ręcznaWiertarka ręczna
12

Paint and finish

Give the canvas a coat of shellac to waterproof it, then four coats of paint to fill the fibres, rubbing down the second and third with fine sandpaper. Finish all woodwork with three coats of good outside spar varnish. A removable slatted grating of soft-pine lattice, about 1-1/8 in wide and 1-1/4 in thick as printed, screwed to curved cross strips (not the ribs), protects the bottom.

Materiały do tego kroku:

Politura szelakowaPolitura szelakowa1 sztuka
Farba olejnaFarba olejna1 sztuka
Papier ściernyPapier ścierny1 sztuka
Lakier jachtowyLakier jachtowy1 sztuka
Deska sosnowaDeska sosnowa1 sztuka

Potrzebne narzędzia:

Pędzel szerokiPędzel szeroki
Wkrętak płaskiWkrętak płaski
13

Troubleshooting

Canoe troubleshooting.

Flow

Loading...
14

History and honest limits

From "How to Build a Canoe, Part I" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 77-84). As printed, his text differs in places: the backbone's lower edge is 1/2 in longer in one sentence and 1 in in the next; the list gives No. 8 deck screws, the text No. 10; the list's seat frames (30 x 3 and 12 x 2-1/4 in) differ from Fig. 10 (29 x 9 in); the fenders are half-round in the list and round in the text. The metric figures are ours.

Materiały

16

Wymagane narzędzia

21

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...