Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Thimble: the Pitted Iron Thimble Gilt Inside (Rouy and Berthier, Ure 1839)
Forge

Autor

Forge

4. listopad 2026NO
13
0
0
0
0

Thimble: the Pitted Iron Thimble Gilt Inside (Rouy and Berthier, Ure 1839)

The Paris method of Rouy and Berthier: thin sheet-iron discs, red-hot, punched step by step into a cup through five ever-deeper hollows, then turned, pitted and annealed on the lathe, gilt inside with gold leaf pressed on by a steel mandril, and banded outside with a gold fillet. Variable: closed (pitted round end) or open (no end, for tailors). Source: Andrew Ure, Dictionary of Arts, Manufactures and Mines (1839), 'Thimble'. Picture: a modern pitted thimble (Commons, CC BY-SA 3.0).
Zaawansowany
Unknown

Instrukcje

1

Punch the blanks

Cut sheet iron 1/24 in thick into strips sized for the thimbles. Run them under a punch press to cut discs about 2 in across, left joined by a tail, a dozen to a strip.

Materiały do tego kroku:

Blacha żelazna (kuta)Blacha żelazna (kuta)1 1/24 in

Potrzebne narzędzia:

Prasa wykrojnikowaPrasa wykrojnikowa
2

Sink the cup

Heat the blanks red-hot and lay each on a mandril fitted to its size. Strike the middle with a round-faced punch about as thick as a finger to sink it into the first hollow, then drive it through a block with five hollows of increasing depth until it has the thimble's shape.

Potrzebne narzędzia:

Palenisko kowalskiePalenisko kowalskie
SzczypceSzczypce
Nieznany metalNieznany metal
MłotekMłotek
3

Turn and pit on the lathe

Chuck the rough thimble in the lathe, polish the inside, turn the outside, mark the rings for the gold band, and press in the rows of pits with a milling tool.

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
RadełkownicaRadełkownica
4

Anneal, gild and band

Anneal and brighten the thimbles. Line each inside with a thin cone of gold leaf, bonded to the iron by the hard pressure of a smooth steel mandril. Turn an annular seat outside, lay a gold fillet in it and press its edges into a fine groove cut on the lathe.

Materiały do tego kroku:

Złoto płatkoweZłoto płatkowe1 lining
Nieznany metalNieznany metal1 gold fillet

Potrzebne narzędzia:

Palenisko kowalskiePalenisko kowalskie
Pręt trzpieniowyPręt trzpieniowy
Tokarka do metaluTokarka do metalu

Materiały

3

Wymagane narzędzia

8

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...