Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Vacuum Gauge: Flattened Curved Tube Driving an Index (Bourdon, US 9,163)
Emma

Autor

Emma

9. listopad 2026SE
3
0
0
0
0

Vacuum Gauge: Flattened Curved Tube Driving an Index (Bourdon, US 9,163)

A vacuum gauge shows how far a line or vessel has been pumped below atmospheric pressure. Eugène Bourdon (US 9,163, 1852) found that a thin metal tube, flattened and bent into a curve, straightens a little under internal pressure and curls up more when the air is drawn out of it. One end is open to the line through a cock; the closed end drives a lever on a spindle that carries the index. With the air withdrawn the index moves the opposite way to a pressure gauge, "and the instrument is then a vacuum gage." Source: E. Bourdon, "Pressure-Gage", US Patent 9,163 (1852). Picture: its Figs. 1-6.
Zaawansowany
Unknown

Instrukcje

1

Read Bourdon

"If the air be withdrawn from the interior of the tube A by means of an air pump or otherwise the curvature of the tube is increased and the index moves in the opposite direction and the instrument is then a vacuum gage."
2

Make the tube

Flatten a thin metal tube so its section is no longer round (Bourdon draws oval, flat, cross and Y sections) and bend it into a near circle. Close one end (how is not given) and leave the other open. Bourdon: the wall depends on the size, motion, pressure and metal; his only figure is brass about 1/100 in. thick for a barometer about 4 in. across. The metal, wall and size for the vacuum gauge are not given.

Materiały do tego kroku:

Nieznany metalNieznany metal1 tube

Potrzebne narzędzia:

Nieznana metoda kształtowaniaNieznana metoda kształtowania
Nieznane wymiaryNieznane wymiary
3

Fit the movement

Fix the open end of the tube in the case, connected through a cock to a pipe to the line or vessel. Join the closed end by a link to a short lever on a small spindle that carries the index (or drive the spindle by a toothed sector and pinion, or by a silk thread wound round it and kept tight by a spring). The lever multiplies the tube's movement at the index.

Materiały do tego kroku:

Nieznany zawórNieznany zawór1 cock
Nieznany metalNieznany metal1 link, lever, spindle and index
Nieznany metalNieznany metal1 case

Potrzebne narzędzia:

Wiertarka stołowaWiertarka stołowa
Zestaw wiertełZestaw wierteł
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
4

Graduate the dial

Fit a dial behind the index. Bourdon graduates the arc by submitting the instrument to known pressures alongside an ordinary mercury gauge and marking each on the dial; equal steps of pressure give nearly equal degrees. Connect the gauge to a pump drawing the air out: the tube curls more and the index moves the opposite way to a pressure gauge. The reference used to mark a vacuum scale is not given.

Materiały do tego kroku:

Nieznany materiałNieznany materiał1 dial

Potrzebne narzędzia:

Pompa próżniowaPompa próżniowa

Materiały

3

Wymagane narzędzia

6

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...